What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Screw model Drive Code: groove on the head, characteristic model Length Code: screw length (mm) A-1: Thread Code: screw model Metric screws directly indicate the screw model with the outer diameter of the screw, such as M3, the outer diameter of the screw is 3.00mm. ; M4 means the outer diameter of the screw is 4.00mm. Metric Thread Size x Pitch: Note: The metric screw is behind the screw model, and sometimes the screw pitch is indicated. Such as M3x0.5, M4x0.70, M5x0.8, M6x1. Standard specification, usually not mentioned. A-2: Length Code: Screw length: For metric screws, the screw length is directly marked in mm. The total length of the screw is marked, only the length below the head is calculated, excluding the head height. But With the exception of flat head screws, the total length of the screw is marked with the head height. A-3: Drive Code/ Head Groove, Features.
The spring washer is designed for screw backstop, usually a single-turn cylindrical coil spring. In order to improve its backstop function, there is also an integrated spring washer. Its structure is that the inner ring of the flat washer has multiple wings. Fold into spring tabs. Another type of washer used for backstop similar to spring washers is a serrated lock washer. However, this kind of lock washer usually has a small thickness, which is formed by folding the inner ring or the outer ring of the washer on the plane. When tightening, the elastic force is small, and the second is easy to be flattened, so that the stop The retreat function is still not strong enough.
For hexagonal nuts, the commonly used standards are: GB52, GB6170, GB6172 and DIN934. The main differences between them are: the thickness of GB6170 is thicker than that of GB52, GB6172 and DIN934, commonly known as thick nuts. The other is the difference between the opposite sides, the opposite sides of DIN934, GB6170 and GB6172 in the M8 nut series are 13MM smaller than the opposite side 14MM of GB52, and the opposite sides of M10 nuts, DIN934 and GB52 are 17MM. The opposite side of GB6170 and GB6172 should be 1MM larger, M12 nut, DIN934, GB52's opposite side is 19MM larger than GB6170 and GB6172's opposite side 18MM is 1MM larger. For M14 nuts, the opposite side of DIN934 and GB52 is 22MM, which is 1MM larger than the opposite side of GB6170 and GB6172, which is 21MM. The other is the M22 nut. The opposite side of DIN934 and GB52 is 32MM, which is 2MM smaller than the opposite side of GB6170 and GB6172, which is 34MM. (Besides the thickness of GB6170 and GB6172 are the same, the width of the opposite side is exactly the same) The rest of the specifications can be used in general without considering the thickness.
Align the four positioning holes 12-5 of the spring washer positioning plate 2 with the four positioning columns 4 of the screw tray 1, and place them on the screw tray 1. Several screws 5 are passed through the lower positioning plate 12-2 in turn. The spring washer hole 2-7, the opening slot 12-32 of the baffle plate 12-3, the inner ring of the spring washer 7 in the spring washer hole 2-7 of the upper positioning plate 12-1, hold the spring washer positioning plate 2 by hand The raised handle 12-31 of the baffle plate 12-3 pulls the baffle plate 12-3 out of the upper positioning plate 12-1 and the lower positioning plate 12-2, and several spring washers 7 pass through the holes on the lower positioning plate 12-2. The spring washer holes 2-7 fall down along the screw rod of screw 5, so that the screw rod of screw 5 penetrates into the spring washer 7, as shown in Figure 10, and then the spring washer positioning plate 2 is removed to complete the process of threading the spring washer.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
