Machjong machine with non-standard positioning screws flat head cross recessed step screw 3/4 5/8

We have more than ten years of production experience in the screw industry, the main products are: stainless steel mushroom head screws, large-head knurled hand-tightened screws and bolts, enterprise copper nuts, thickened opening spring washers, corrugated gaskets, imported raw material screws, car cover screws Caps, Q235 hot-dip galvanized screws, wire rope tensioning screws, electric water heater expansion screws, DIN316 hand-tightening bolts, Class A American standard gaskets, flat washer combination set screws, 1587 hexagonal cap nuts, Q440 rivets and other fasteners, Due to the different materials and specifications of the products, the prices are also different, please contact us if necessary.

Online consultationMobile hotline
132 6870 6820
Product introduction

Screw Specifications

Screw head table

Traditionally, the pressure rivets on the product are all beaten by hand by workers, resulting in high scrap rate and low efficiency, and this rivet is not a traditional rivet, so it is difficult to locate and requires high pressure. The rivets are thin, and the pressure is too large to cause deformation of the rivets. If the pressure is too small, it cannot be riveted. Without special positioning and tooling, it cannot be riveted on the riveting machine. The quality of the products produced in this way is difficult to guarantee, and the quality levels of the products in the same batch are uneven. Affect delivery time.

Non-standard processing for mahjong machines

At present, the commonly used fastener loosening prevention methods generally include non-removable anti-loosening solutions and friction-increasing anti-loosening solutions. The non-removable anti-loosening scheme uses welding, bonding or punch point riveting to change the detachable threaded connection into a non-detachable threaded connection. In the non-removable anti-loosening scheme, the threaded fasteners cannot be reused and the operation is troublesome. It is often used in some important occasions that require high anti-loosening performance without disassembly. The anti-loosening scheme that increases the frictional force uses the method of increasing the frictional force of the bolt (screw) head and the end face of the nut to achieve the purpose of anti-loosening. The anti-loosening solution that increases friction is not limited by space and can be disassembled repeatedly, but the reliability is poor. After a certain period of work, the anti-loosening effect will be reduced due to vibration and other reasons.

set screw

Flat Head Cross Recessed Step Screws

At present, in the power industry, for the fixing of terminals, most of the terminals are directly locked to the fixing screws using U-shaped clips. However, since the contact surface often cannot reach the level of flatness, it will cause difficulties in locking, and it will take a long time. Easy to loose and fall off. Although the use of spring clips is effective, due to the influence of its own width, the use of spring clips is not very extensive. Contents of the utility model The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to provide an automatic locking screw for fixing the U-shaped clip. In order to achieve the above purpose, Yueluo adopts the following technical solutions: an automatic locking screw. From bottom to top, there are screw head, screw rod and nut with external thread. The screw rod is a hollow screw rod, and the hollow screw rod is on both sides. Long holes are respectively provided, the width of the long holes is smaller than the inner diameter of the hollow screw rod, a spring is arranged in the inner cavity of the hollow screw rod, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole. The spring described by Yueluo is not less than the length of the hollow screw rod in the free extension state. The distance between the two wings of the plug described by Yueluo is greater than the diameter of the nut. Yueluo adopts Guangdong Yueluo Hardware Industry Co., Ltd., which can easily realize the automatic locking of the U-shaped clamp, and can be adjusted according to the thickness of the U-shaped clamp to ensure the close contact between the U-shaped clamp and the connecting screw.


The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a new type of open blind rivet suitable for riveting of aluminum Al, steel St, and stainless steel SST sheets with foam material in the middle. The new rivet improves the mandrel process, adopts aluminum mandrel, the head of the mandrel has a pit for easy deformation, and there is a conical stop groove above the breakpoint of the mandrel. The mandrel can be caught by the stopper to prevent the nail head from being exposed. At the same time, lock the core rod not to loosen.


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].

Cooperation Case

Hot Recommend