What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
The structure of Guangdong Yueluo Hardware Industry Co., Ltd. is as follows. Figure 1 is a schematic diagram of the structure of the existing pin shaft stop mode of a general excavator. Figure 2 is a schematic structural diagram of the pin shaft stop used by Guangdong Yueluo Hardware Industry Co., Ltd. for applying the bolt of Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 3 is the left side view according to Fig. 2 of the bolt used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 4 is the front view of Guangdong Yueluo Hardware Industrial Co., Ltd., which is used for the pin shaft stopper to insert the pin into the pin and form the pin of the pin structure. Fig. 5 is the left side view of Guangdong Yueluo Hardware Industry Co., Ltd., which is used for the pin shaft stopper to insert the pin into the pin and form the pin of the pin structure. Fig. 6 is a front view of the bayonet of the latch used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 7 is a top view of a bayonet of a latch used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 8 is the front view of the circlip of the latch used by Guangdong Yueluo Hardware Industry Co., Ltd. for pin stop. [0017] FIG. 9 is a top view of the circlip of the bolt that Guangdong Yueluo Hardware Industrial Co., Ltd. is used for pin-stopping. In Figures 1 to 9, the latch (1), the retaining sleeve (2), the pin shaft (3), the bayonet (4), the circlip (5), the misaligned through hole (6), and the misaligned end head (7).
The combination screw includes a head, a threaded section and a flanging section, the flanging section is arranged below the threaded section, and the flanging section and the threaded section pass through the mounting holes on the fittings, so that the combination screw and the fittings are rotatably connected, so After the flanging section passes through the fitting, the bottom of the flanging section is riveted and pressed so that the bottom of the flanging section is turned outward, so that the combined screw cannot be separated from the fitting.
If you are installing rivet nuts specially, you can use a grinder, use a rivet machine, if you are a non-professional, you can directly install a few, and then tap with an awl. Rivet equipment (manual or pneumatic) cannot be used in the field of fastening using hammers to pull rivet nuts. It is widely used and is mainly used in the assembly of electromechanical and light industrial products such as aviation, furniture, automobiles, instruments, machinery, and decoration. Of course, it is more common than the rivet nut, and it is often difficult to distinguish.
rotating rod is rotatably installed on one side of the two pillars that are close to each other, and a second bevel gear is welded on the ends of the two rotating rods that are close to each other. The two second bevel gears are meshed with the two first bevel gears respectively. , The first sprocket is welded on the two rotating rods, the chain is meshed on the two first sprockets, and the screw rods are installed on the sides of the two pillars that are close to each other. Above the rod, the second sprockets are welded on the two screw rods, the two second sprockets are connected to the two first sprockets through two chains respectively, and threaded blocks are threaded on the two screw rods. The sides of the two threaded blocks close to each other are symmetrically welded with connecting columns, and the sides of the four connecting columns close to each other are welded with movable rods respectively. The other ends of the support plates are respectively rotatably installed with the same support plate, and the assembly device body is fixedly installed on the top of the support plate.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
