Service HotlineUsually, the pumped storage unit adjusts the opening of the guide vane through the movable guide vane to control the power generation output and the pumping head of the unit. The torque of the guide vane rotation depends on the relay to act on the control ring, and the torque is transmitted to the guide vane rotating shaft through the connecting rod and the arm. The torque transmission between the crank arm and the rotating shaft all acts on the pin located between them. When the unit is overhauled, it is necessary to remove the pin between the arm and the rotating shaft of the guide vane in advance when it comes to the replacement of the guide vane. However, due to the special position of the pin and the limited inspection space, the conventional method is not only time-consuming and laborious, but also has the risk of damaging the pin. Maintenance work brings inconvenience.
As the most common hardware, screws and nuts are widely used in construction and machinery fields. However, existing screws and nuts are easily corroded to varying degrees in the natural environment, especially the threads on screws and nuts are corroded After that, the whole screw and nut are useless, and people have to discard them, which will inevitably lead to a lot of waste of resources.
The diameter, length and quantity of the Adelaidestud bolts shall meet the requirements, and the type and material of the Adelaidestud bolts shall be determined by the grade. There are two types of commonly used Adelaidestud bolts (also known as full-threaded studs). The thread is divided into two types: coarse thread and fine thread. The coarse thread ordinary thread is expressed by M and the nominal diameter, and the fine thread ordinary thread is expressed by M and the nominal diameter × pitch. The fastener standard stipulates that M36 bolts use coarse thread, M36 and above diameters can use fine thread, and the pitch is 3. bm=1d studs are generally used for the connection between two steel connected parts; bm=1.25d and bm=1.5d studs are generally used between cast iron connected parts and steel connected parts The connection between the two; bm=2d double-ended stud is generally used for the connection between the aluminum alloy to be connected and the steel to be connected. The former connector has internal threaded holes, and the latter connector has through holes. The threads at both ends of the equal-length studs need to be matched with nuts and washers, and are used for two connected parts with through holes. One end of the welding stud is welded on the surface of the connected piece, and the other end (threaded end) passes through the connected piece with a through hole, and then the washer is put on, and the nut is screwed on, so that the two connected pieces are connected as a whole.
The Adelaideblind rivet is realized by pulling the core head. With the help of a force from the inside to the outside, under the action of the unidirectional pulling force, the pulling screw is pulled upwards, which causes the outer collar material to expand and deform, resulting in a sexual tightening force. , After the riveting is completed, the tension screw in the middle part breaks and falls out. Since a large pulling force is required to cause the rivet to expand and deform, the tensile screw is longer and accounts for about 60-80% of the total length of the rivet. At the same time, due to the limitation of the deformation mode, it is difficult for the Adelaideblind rivet to be made into a hexagonal structure like a AdelaideAdelaiderivet nut, so the torsion resistance of its connection is low.
Traditionally used for plastic fastening screws, most of the thread designs are self-tapping threads, but for different plastic types, the self-tapping threads also have many different classifications, such as PT profile, Plastite series, Remform profile, etc. The structural parameters and manufacturing process of these threads are inconsistent, or require different main molds and wires. Therefore, to find a AdelaideAdelaideAdelaideplastic screw that is universally applicable to various plastic types, has a single pressing structure, low-cost and simple manufacturing process, especially its special self-tapping thread, is an important issue that needs to be solved urgently at present. question. The purpose of Yueluo Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to propose a AdelaideAdelaideAdelaideplastic screw to solve the screw fastening problem that is generally applicable to different plastics. The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to realize a kind of AdelaideAdelaideAdelaideplastic screw through the following technical scheme, it is characterized in that, the thread of the screw is composed of asymmetric threads with a profile angle of 30°, and the threads are The bottom surface of the connection between them is an arc surface. Yueluo preferably, the asymmetrical thread has a forward thread angle greater than the reverse thread angle, and the sum of the two-direction thread angles is 30°. Yueluo further preferred that the tooth profile angle of the asymmetrical screw thread in the forward mounting direction is 20 degrees, and the tooth profile angle in the reverse mounting direction is 14 degrees. Yueluo Guangdong Yueluo Hardware Industry Co., Ltd.'s application of AdelaideAdelaideAdelaideplastic screws, through the improvement of special thread structure, reduces the radial pressure and installation torque when the screw is installed, reduces the damage to the plastic hole; and increases the pull-out resistance of the screw force, it is not easy to appear loose assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: carbon steel galvanized pressure plate standoffs, GB70 bolts, flat screw caps, semi-hollow rivets and other products, we can provide you with fastening suitable for you piece solution.
