structure for concealing installation screws, comprising a locking piece, a driving piece, a bottom plate, a blocking cover and a handle head, the lower ends of the two locking pieces are provided with positioning holes, and the locking pieces pass through the positioning holes and the locking piece positioning posts on the base The occlusal and fixed, the middle of the two locking pieces is provided with a protruding point, the movable groove of the driving piece corresponds to the protruding points of the three locking pieces for fixing, the riveting point holes and screw holes of the bottom plate and the riveting points of the base The position that matches the screw holes and is fixed by screws, the blocking cover is directly inserted into the bottom plate, and the blocking cover is fixed by the rotating drive piece, the handle head is inserted into the base, and the slot of the handle head moves to the locking piece at the locking piece Lock the handle.
screw with a gasket aims to provide a screw with a gasket that improves installation efficiency. The technical solution of the screw is that after the screw cap, the connecting rod and the screw rod are processed, the gasket with the installation through hole is processed. The installation through hole is drilled through the connecting rod, and then the end of the screw rod opposite to the connecting rod is processed to form a convex tooth structure by extrusion. At the same time, the outer diameter of the tooth peak of the convex tooth is larger than the inner diameter of the installation through hole, so that the gasket is not easy to be installed. Falling off, the step of manually wearing the gasket is reduced, that is, the workload of the staff is reduced, and the installation efficiency is relatively high. The flange increases the contact area between the screw cap and the gasket, and enhances the friction between the screw cap and the gasket, which can prevent the screw from loosening easily after being fastened and installed, thereby improving the connection stability of the screw. When installing the screw, the fixing part can be snapped into the fixing groove on the installation plane, so as to avoid the washer from rotating with the rotation of the screw when the screw is tightened, which is convenient for the tightening and installation of the screw.
In general, the size, mechanical properties and working performance requirements of self-tapping screws have the following standards: 1. AucklandSelf-tapping screw size standard ASME B18.6.3 2010 standard not only introduces the dimensions of slotted and cross-recessed self-tapping screws and metal drive screws, but also includes the mechanical properties and work performance requirements of carbon steel self-tapping screws. The appendix gives instructions for measuring the various dimensions and application guidance on clamping lengths and test apertures. 2. AucklandSelf-tapping screw performance standards (including mechanical properties and work performance): (1) SAE J933: Introduces the mechanical performance and work performance requirements of carbon steel ordinary self-tapping screws and white-cut self-tapping screws. The requirements for selection of raw materials, heat treatment, depth of carburized layer, surface hardness, and core hardness are further specified. (2) SAE J81: The mechanical properties and working performance of self-extrusion self-tapping screws (self-tapping locking screws) are introduced. (3) SAE J78: The mechanical properties and working properties of self-drilling and self-tapping screws are introduced. (4) IFl-113: The mechanical properties and working properties of self-drilling and self-tapping screws are introduced. (5) ASTM C1513: Introduces the mechanical properties and performance requirements of carbon steel self-tapping screws. For other special types of self-tapping screws, there is no corresponding national or industrial standard, and no data for self-tapping screws made of other metal materials other than carbon steel have been recognized. For technical data on these self-tapping screws, you can check with the manufacturer.
A nut provided by Yueluo. The nut is in the shape of a sleeve and has a threaded section inside. An annular groove is set on the inner wall of one end of the threaded section. The notch of the groove points to the hole core. The hole diameter at the groove notch at the front end is larger than the nominal size of the thread segment or the hole diameter at the groove notch at the rear end in the screwing direction is smaller than the nominal size of the thread segment.
AucklandFasteners are widely used in nuclear power plant safety systems and equipment, and undertake the functions of component connection, pressure sealing box support and fixation, and their quality and performance play an important role in nuclear power plant safety systems and equipment performing nuclear safety functions. None of the special fasteners for nuclear power in the prior art have protective sleeves, which cannot protect the exposed part of the bolt shank. In order to solve the above difficulties, it is necessary to develop a fastener stud nut washer set that can protect the exposed part of the bolt shank.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat cylinder bolts, gasket sets 12.9, anti-loose washers, spacer copper studs and other products, we can provide you with suitable products for you. AucklandFastener Solutions.