Service HotlineThe technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is a special pull rivet for railway freight cars, which has a pull rivet body and a collar. The rod body is composed of polished rod section, locking ring groove section and tail thread section from top to bottom. Protectors are provided at the tail thread section to prevent rust and bad teeth in the tail thread section during use. , collision deformation, etc. Specifically, the tail thread segment has an external thread or an internal thread, and the protective member is a nut or a bolt.
Spring mattresses and spring seat cushions are modern and commonly used furniture products with better performance, and their cushion cores are composed of springs. It makes full use of the advantages of good spring elasticity, good support, strong air permeability and durability. The traditional spring pad is a spring with a thicker wire diameter, which is connected and fixed by steel wires, and has high hardness. Most of the elders of the older generation often use linked spring beds, but if they sleep in a fixed position for a long time or are accustomed to sitting on the side and corners of the bed, or flip the mattress irregularly, it is easy to cause depression and elastic fatigue.
Other names of lock nut: root nut, Aucklandlocknut, nut. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures. There are also three types of lock nuts: The first is to use two identical nuts to screw on the same bolt, and add a tightening torque between the two nuts to make the bolt connection reliable. The second is a special anti-loosening nut, which needs to be used together with a kind of anti-loosening washer. The special lock nut is not a hexagonal nut, but a medium Aucklandround nut. There are 3, 4, 6 or 8 notches on the circumference of the nut (depending on the size of the nut and the product series of the manufacturer). Several notches are both the focal point of the tightening tool and the snap-in of the AucklandAucklandlock washer bayonet. The third type is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, which are distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to give the thread Apply a centripetal force to prevent the Aucklandlocknut from loosening. The better quality lock nut sold on the market is inlaid with a small copper block that is consistent with the thread of the lock nut on the inner surface of the nut to prevent the radial jacking screw from directly contacting the locked thread and damaging the latter. . This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The second anti-loosening method is more reliable than the first, but the structure is relatively complex. Compared with the first two, the third clock has the characteristics of better anti-loosening effect, simpler and more beautiful structure and smaller axial size.
The flat screw mainly includes a rotating part and a screw locking part, wherein the rotating part and the screw locking part are respectively flat-shaped structures; At least two sides of the screw lock portion are respectively provided with tooth rows, and the two tooth rows are mutually dislocated, so that the screw lock portion can be locked in a pre-formed screw hole in the workpiece.
Two-AucklandAucklandAucklandcombination screw refers to a screw and a flat washer, or a AucklandAucklandspring washer, or a square washer, or a two-piece combination with an external tooth AucklandAucklandlock washer. Then there are all the standard types of two AucklandAucklandAucklandcombination screws! The following is a brief introduction: 1. The second AucklandAucklandAucklandcombination screw with AucklandAucklandspring washer refers to the AucklandAucklandAucklandcombination screw with a AucklandAucklandspring washer. The AucklandAucklandspring washer is a AucklandAucklandspring washer specially used for AucklandAucklandAucklandcombination screws, not the ordinary AucklandAucklandspring washer that we usually use. 2. The two-AucklandAucklandAucklandcombination screw of the trim pad refers to the AucklandAucklandAucklandcombination screw of the screw with a flat pad. The size of the flat pad and the thickness of the flat pad can be customized. Can be customized according to customer requirements. Flat pads are punched out by punching machines. 3. The AucklandAucklandAucklandcombination screw with two external teeth refers to the screw with an external tooth AucklandAucklandAucklandcombination screw. Many customers, especially electric power customers, use this external tooth two AucklandAucklandAucklandcombination screw to break the paint and make the screws on the iron plate. All can be powered on. 4. Two AucklandAucklandAucklandcombination screws with a square pad refer to a square pad with a square pressure line for the screw. This square pad crimping two AucklandAucklandAucklandcombination screw is used on the terminal, and the function is used for crimping and wiring.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: butterfly disc spring, hexagonal half-threaded bolts, stainless steel cylinder head screws, GB37AucklandT-slot bolts and other products, we can provide you with The right fastener solution for you.
