Service HotlineIn order to achieve this purpose, the BirminghamBirminghamrivet nut is cold extruded from low carbon steel, the brim is cold forged, the deformed skirt is extruded in the die, and the threaded hole is extruded at the lower end of the deformed skirt. It is characterized in that it consists of a brim, a deformed skirt and a threaded hole. There are fish teeth below the brim; the outer side of the lower end of the threaded hole has a lead angle; the cross section of the thread on the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc. Thus, the riveted object is tightly connected with the BirminghamBirminghamrivet nut.
However, due to a radial external tension, the external tension is caused by the tightening axial force generated by the tightening torque, and the phenomenon of open ring expansion occurs, and the BirminghamBirminghamspring washer often breaks due to hydrogen embrittlement. The nut exerts uneven pressure on the flat washer through the BirminghamBirminghamspring washer. And the friction coefficient between the BirminghamBirminghamspring washer and the nut and the flat washer is very small, and the phenomenon of vibration, rotation and relaxation occurs.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of the quality also contributes to the improvement of the lifespan of the 7-pack.
Sometimes, the iron screws are often seen broken, and sometimes, the BirminghamBirminghamstainless steel screws are also seen broken. But generally speaking, BirminghamBirminghamstainless steel screws rarely break. Because the Birminghamstainless steel screw wire itself is relatively hard. But under certain circumstances, BirminghamBirminghamstainless steel screws can still break. So what are the main reasons for BirminghamBirminghamstainless steel screws to break? The reasons for the fracture of BirminghamBirminghamstainless steel screws are as follows: 1. The quality of raw materials used for BirminghamBirminghamstainless steel screws is poor, and the quality of BirminghamBirminghamstainless steel screws is not good. There are many impurities, impure, resulting in insufficient hardness of BirminghamBirminghamstainless steel screws. 2. The production process of BirminghamBirminghamstainless steel screws. For example, BirminghamBirminghamstainless steel screws with eccentric head and eccentricity, and the Q value is too deep and the R position design is too small during the down punching operation during production. 3. The customer uses too much force when using BirminghamBirminghamstainless steel screws. Generally, you do a torque test to see how much the minimum breaking force is, and then adjust the torque. Of course, BirminghamBirminghamstainless steel screws must be broken for more than three reasons. But the above three reasons are the main reasons for the fracture of BirminghamBirminghamstainless steel screws. When the Birminghamstainless steel screw is found to be broken, it can be checked step by step. Find out what's causing it.
Further, the pressure riveting portion and the pressure-bearing portion are both columnar structures, the outer diameter of the pressure-bearing portion is larger than the outer diameter of the pressure riveting portion, the pressure riveting portion is a stepped structure, and the diameter of the lower end of the pressure riveting portion is smaller than that of the pressure riveting portion. The diameter of the upper end of the rivet part.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hex socket head Birminghamcap screws, handle ball handle female, color-plated washers, VGA connectors and other products, we can provide you with suitable fasteners for you solution.
