Service HotlineBradfordGaskets are widely used in the machinery industry. According to the different needs of machinery and equipment in different industries, the structural forms of the sealing points are also different. Plum washer is one of the commonly used seals. It is commonly used between the pump and the motor coupling. In the actual production process of the enterprise, it is found that due to the influence of the material and structure, this type of gasket in common use can withstand impact force. Small, the septum is easily damaged. Because the current plum washers are all one-piece structures, even if one or several of the partitions are damaged, they need to be replaced as a whole. Although the value of a single plum washer is low, it needs to be shut down for maintenance and replacement almost every week. It also seriously affects the normal production of the enterprise, and the one-piece plum blossom gasket is also difficult to repair, adding unnecessary use costs to the enterprise. For this reason, the plum blossom gasket needs to be improved to strengthen the impact resistance of the gasket, and can be repeated Maintenance and use, prolong the maintenance cycle of the equipment, and ensure the normal production of the enterprise. The purpose of the utility model Yueluo is to solve the above-mentioned deficiencies in the existing technology, improve the existing technology, and provide a simple structure, which strengthens the impact resistance of the gasket, and can be repeatedly maintained and used to prolong the maintenance of the equipment. The cycle guarantees the plum blossom elastic washer normally produced by the enterprise. In order to achieve the above purpose, Yueluo is achieved through the following technical solutions-namely a plum blossom elastic washer, including an elastic washer body with a partition, the technical point is that the washer body is composed of a washer base and a partition that is independent of each other. , the septum and the gasket base are fixedly connected into one through the fixing piece. In order to further strengthen the impact resistance of Yueluo, the contact parts of the spacer and the washer base are respectively processed with a limited clamping table and a matching groove, so that the spacer and the washer base can be better integrated into one. According to the different specifications of the torx washer, the spacer and the washer can be fixed as a whole by rivets; or by screws. In addition, a semi-rigid tightening ring with grooves is embedded inside the washer base, and the width of the tightening ring is smaller than the width of the washer base; the ends of the rivets or screws are located in the grooves of the tightening ring, so as not to affect the performance of the torx washer JH is often installed. After the above improvement, Yueluo has improved the one-piece structure of the plum-blossom washer into a split structure and adopted a variety of fixed structure forms, so it has a simple structure, strengthens the impact resistance of the gasket, and can be repeatedly maintained and used. , Extend the maintenance cycle of the equipment and ensure the advantages of the normal production of the enterprise.
Hot rolled wire rod before plating process - (cold drawing) - spheroidizing (softening) annealing - mechanical dephosphorization - pickling - cold drawing - cold forging - threading - heat treatment - inspection
The technical process of nickel-phosphorus plating for high-strength bolts consists of three parts: The first part is the pre-treatment process, including the precision and appearance inspection of high-strength bolts before plating, manual degreasing, immersion degreasing, pickling, electro-activation and flash nickel plating and other processes; the second part is the electroless nickel plating treatment process; the third part is the post-treatment process, including the processes of hydrogen-displacing heat treatment, polishing and finished product inspection. As follows: Bolt chemical composition inspection → bolt pre-plating accuracy, visual inspection → manual degreasing → visual inspection → immersion degreasing → hot water washing → cold water washing → pickling → cold water washing → electric activation → cold water washing → flash nickel plating → cold water washing → Deionized water washing → Electroless nickel plating → Deionized water washing → Cold water washing → Hydrogen removal → Polishing → Finished product inspection.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of quality also contributes to the improvement of the lifespan of the 5-pack.
High-strength fastener materials mainly include ML35, 35K, ML40Cr, ML35CrMo steel, etc., of which 75ML35CrMo steel is imported. The main problems of the material are box segregation, decarburization, cracks and so on. The material needs to be spheroidized and annealed before cold forming, and the annealing is carried out in an oil furnace. There is no protective atmosphere in the furnace, and there is a decarburization phenomenon. 1.2 The high-strength fasteners, mainly grade 12.9, are quenched and tempered on the chain casting furnace production line. The temperature and atmosphere in the furnace are controlled by computer, and Rx gas is used as a protective atmosphere. Heating and anti-oxidation and decarburization can be effectively controlled, and the quality of the fasteners is intact during the heating process. The high-strength fasteners mainly of grade 8.8 are quenched and tempered on the vibrating hearth furnace. Affected by the structure of the vibrating hearth furnace, the sealing performance of the furnace is poor, the Rx atmosphere is not easy to control, the temperature difference of the furnace is large, and the parts are heated in the furnace. The collision and the length of time are inconsistent, and the quality of the fasteners during the heating process is poor, and there are phenomena such as decarburization, bumps, and uneven heating.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 2205 screws, self-locking anti-theft locking screws, DIN pins, pure titanium screws and other products, we can provide you with suitable fasteners for you solution.
