Service HotlineThe side wall of the bolt hole is threaded, and the top of the nut is provided with several flattening notches. According to the locking nut of the preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the number of flattening notches is three. Due to the above features, the three flattening notches can be used as the focal point of the tightening tool, and the
In order to solve this technical problem, Yueluo Company provides an adjusting nut, which includes a bearing unit, a thrust washer, an adjusting nut and a snap ring. The inside of the adjusting nut is an internal thread structure, and one end of the internal thread structure is provided with Ring groove, the snap ring is pressed into the ring groove with interference, and is rigidly connected with the adjusting nut without relative movement; the bearing unit is supported on the shaft, and the thrust washer is in plane fit with the bearing unit; the adjusting nut and the shaft are threadedly connected , Fit with the thrust washer plane, the inner diameter of the snap ring and the thread of the shaft are in interference fit.
ANSI B1.1 Thread Pitch Comparison Table Nominal Diameter (inch〖mm〗) Coarse Thread Pitch (UNC) Fine Thread Pitch (UNF) Ultra Fine Thread Pitch (UNEF) Drilling Diameter (Coarse Thread) Drilling Diameter (Fine Thread) #0 0.060 〖1.524〗 80 1.2 # 1 0.073 〖1.5 1.5 # 2 0.086 〖2.8 # 3 0.099 〖2.515〗 48 56 2.0 2.1 # 4 0.112 〖2.4 # 5 0.125 〖 3.175〗 40 44 2.5 2.6 # 6 0.138 〖3.50〗 32 40 2.7 2.9 # 8 0.164 〖4.166〗 32 36 3.4 3.5 # 10 0.190 〖4.0 # 12 0.216 〖5.486〗 24 28 32 4.5 4.6 1/4 6.35 20 28 32 5.1 5.4 5/16 10.7 11.5 9/16 〖14.288〗 12 18 24 12.3 13.1 5/8 〖15.875〗 11 18 24 13.5 14.7 3/4 〖19.05〗 10 16 20 16.7 17.5 7/8 〖22.125 2.4 9 14 〗 8 12 20 22.2 23.4 The pitch is expressed by the number of teeth per inch, such as: 11 teeth per inch, then the pitch=25.4/11=2.309mm. The unit of pitch in the table is the number of threads per inch. The hole diameter is the recommended hole size for tapping, in millimeters.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of quality also contributes to the improvement of the lifespan of the 9 bottles.
When the rivet is riveted, it is often necessary to locate and fix the rivet. However, the common rivet positioning mechanism at present often has no way to effectively and quickly remove the restriction on the rivet after the rivet is fixed, which makes it difficult for the nailing mechanism to be inserted. Quickly drive the positioned rivets.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: small countersunk head bolts, nylon self-locking locking, lifting Bradfordring nuts, screws and nuts, *30120MM titanium nuts and other products, we can provide you with suitable products for you. BradfordFastener Solutions.
