Service HotlineThe Brisbanesquare nut is a fastener that needs to be used in the installation of the cable tray. In the prior art, the Brisbanesquare nut 1 is pressed by the elastic force of the spring 2 below it and the opening of the C-shaped steel 3 (as shown in Figure 1, Figure 2), in the absence of external force, through the interaction of pressure and static friction, the C-shaped steel 3 will not move vertically or horizontally, which can facilitate engineering installation. The advantage of this installation method is that it can slide anywhere on the C-shaped steel 3, but the disadvantage is that it occupies the bottom space of the C-shaped steel 3, and the spring 2 will interfere with the installation hole of the Brisbanesquare nut I, which affects the installation.
GB6177 Hexagon BrisbaneBrisbaneFlange Nuts - Grade GB55 BrisbaneHexagon Thick Nuts GB56 Hexagon Extra Thick Nuts GB1229 Large BrisbaneHexagon Nuts (High Strength for Steel Structure) BrisbaneLock Nuts Other Names: Root Nuts, BrisbaneLock Nuts, and Nuts. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures.
When the mold is manufactured, many positioning pins need to be installed to fix the relative position between the two parts. The positioning pins are usually sunk into the positioning pin holes on the mold. Since the mold needs to be pulled out frequently during assembly, in order to Remove the parts and make corrections. At the same time, the mold also needs to pull out the positioning pins during maintenance to remove the damaged parts for maintenance. Therefore, the workload of pulling the pins is large. The existing methods are: 1) When installing the pins, The operator uses a self-made long screw that matches the threaded hole of the pin to screw it into the pin, and then aligns the pin hole with a hammer to hit the screw to make the pin snap in, and then screw the screw out by hand. The disadvantage is: on the one hand, the hammer hits the screw It is easy to cause the screw to be damaged or deformed, and it cannot be used normally. On the other hand, it is labor-intensive to remove the screw by hand and may not be able to be removed; 2) When pulling out the pin, the operator will screw the screw into the pin and use force directly or with pliers To pull out a screw, a few companies use a large pin puller to pull it out. The disadvantage is that it is too laborious and time-consuming to pull out by hand or with pliers. Even if a large pin puller is used, the weight of the pin puller itself is large. , it is inconvenient to use.
With the rapid development of China's automobile industry, the requirements of body assembly process are constantly improving. Riveting has the characteristics of short process cycle, low noise and low energy consumption, and is widely used in automobile bodies. In the automobile industry, due to the complexity of the body sheet metal structure, there are many cavities, and the riveting tools in some positions will interfere with the structure. Many assembly points cannot use the traditional two-way loading riveting technology, so single-sided riveting is used instead. craft.
The pressure riveting nut, also known as the self-tightening nut, is a kind of nut applied to thin plates or sheet metal parts. To facilitate the installation of other parts on the printed circuit board. The conventional process is to design prefabricated holes on the printed circuit board in advance, and squeeze the BrisbaneBrisbanerivet nut into the board through pressure, so that the periphery of the hole is plastically deformed, so that the BrisbaneBrisbanerivet nut is firmly fixed on the circuit board. In important positions, the use environment of pressure riveting nuts is relatively harsh. In display products, due to space constraints, pressure riveting screws are used a lot. The riveting quality of pressure riveting screws has a direct impact on the reliability of the system. The riveting process is correct. The key technology of using BrisbaneBrisbanerivet nuts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 1769 hexagon slotted nuts, ring Brisbaneexpansion screws, saddle washers, knurled nuts and other products, we can provide you with suitable products for you. BrisbaneFastener Solutions.
