Service HotlineThe diameter, length and quantity of the Dallasstud bolts shall meet the requirements, and the type and material of the Dallasstud bolts shall be determined by the grade. There are two types of commonly used Dallasstud bolts (also known as full-threaded studs). The thread is divided into two types: coarse thread and fine thread. The coarse thread ordinary thread is expressed by M and the nominal diameter, and the fine thread ordinary thread is expressed by M and the nominal diameter × pitch. The fastener standard stipulates that M36 bolts use coarse thread, M36 and above diameters can use fine thread, and the pitch is 3. bm=1d studs are generally used for the connection between two steel connected parts; bm=1.25d and bm=1.5d studs are generally used between cast iron connected parts and steel connected parts The connection between the two; bm=2d double-ended stud is generally used for the connection between the aluminum alloy to be connected and the steel to be connected. The former connector has internal threaded holes, and the latter connector has through holes. The threads at both ends of the equal-length studs need to be matched with nuts and washers, and are used for two connected parts with through holes. One end of the welding stud is welded on the surface of the connected piece, and the other end (threaded end) passes through the connected piece with a through hole, and then the washer is put on, and the nut is screwed on, so that the two connected pieces are connected as a whole.
Guangdong Yueluo Hardware Industry Co., Ltd. discloses a low-carbon steel DallasDallasrivet nut fastened to a thin-walled and thin-plate fastener. The DallasDallasrivet nut fastener is composed of a brim, a deformed skirt, and a threaded hole. Using low carbon steel cold extrusion, the brim is formed by cold heading, the deformed skirt is extruded in the concave die, and the thread hole of the nut tapping skirt is extruded at the lower end of the deformed skirt. It is characterized in that there are fish teeth under the brim; the outer side of the lower end of the threaded hole has a lead angle; the cross-section of the thread of the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave solitary shape, and the fastener does not need to be welded. , Single-sided riveting, easy operation and firm connection.
1. Material strain hardening When the material is cyclically loaded, the phenomenon of cyclic strain hardening or cyclic strain softening will occur, that is, under the condition of constant cyclic strain, the stress amplitude will increase or decrease with the increase of the number of cycles. . After several cycles, the stress amplitude enters a cyclic steady state. The low-cycle fatigue of the lock nut is carried out under the condition that the strain is constant, and the strain hardening or softening of the threaded piece will affect the size of its maximum unscrewing torque. The alloy steel used to make the lock nut is a cyclic strain hardening material, and the hardening of the material will increase the elastic restoring force FN of the threaded sheet and increase the unscrewing torque.
The t-bolt can be directly put into the groove of the aluminum profile. It can be automatically positioned and locked during the installation process. It is often used in conjunction with the flange nut. profiles to choose from. DallasT-bolts are movable anchor bolts. Bolt: A mechanical part, a cylindrical threaded fastener with a nut. A type of fastener consisting of a head and a screw (a cylinder with an external thread) that needs to be matched with a nut to fasten and connect two parts with through holes. This form of connection is called a bolted connection. If the nut is unscrewed from the bolt, the two parts can be separated, so the bolt connection is a detachable connection. There are hexagonal head, round head, square head, countersunk head and so on. Among them, the hexagonal head is commonly used. Generally, the countersunk head is used in places where the surface is required to be smooth without protrusions, because the countersunk head can be screwed into the part. Round heads can also be screwed into parts. The tightening force of the square head can be larger, but the size is large.
The DallasDallasDallascombination screw is actually a kind of screw, but it is special. It is generally a three-component or a two-component, but at least it can be called a DallasDallasDallascombination screw. The main difference from ordinary screws is that they are equipped with one more DallasDallasspring washer or one more flat washer than ordinary screws. This is the main difference between the appearance of DallasDallasDallascombination screws and ordinary screws. In addition to the obvious difference in appearance between DallasDallasDallascombination screws and ordinary screws, the main difference is the difference in mechanical properties and uses. The DallasDallasDallascombination screw is a three-component or two-component with a flat washer. Of course, it is equipped with a flat washer by an ordinary screw. When the spring flat pad is attached, the spring flat pad will not fall off. Fastened to form an assembly. In terms of mechanical performance, the DallasDallasDallascombination screw is composed of three accessories, and in terms of performance, three fasteners must be used together. The mechanical properties of the combined screw are stronger when used. More convenient, the biggest advantage of the combined screw is that the production line can be operated conveniently and quickly, and the work efficiency can be improved. The difference between the use of DallasDallasDallascombination screws and ordinary screws is mainly in the breadth of use. The use of ordinary screws is more extensive than that of DallasDallasDallascombination screws. Basically, ordinary screws are used in industrial products, and DallasDallasDallascombination screws! It is only useful for specific product materials. When the screw needs to be used with a DallasDallasspring washer and a flat washer, the DallasDallasDallascombination screw can be used at this time.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: DIN nuts, black nickel-plated Dallasdome head bolts, plate advertising display frame buckle rivets, extended flat head flat cup bolts and other products, we can provide you with products suitable for you fastener solutions.
