Service HotlineIn the prior art, there are also automated equipment for riveting and assembling of hardware and handles; however, for the existing automated equipment, how to automatically and efficiently realize rivet feeding is particularly important.
A low-carbon steel DublinDublinrivet nut fastener composed of a brim, a deformed skirt and a threaded wire hole is characterized in that there are fish teeth below the brim; the outer side of the lower end of the threaded wire hole has a chamfer; the inner wall of the threaded wire hole The cross section of the thread is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc.
The lifting ring screw should be made of 20 or 25 steel (GB699). The lifting ring screw must be forged as a whole. The forgings should be normalized and the oxide scale should be removed. The grain size of the finished product should not be lower than grade 5 (YB27-77). There must be over-burning, crack defects.
Dublinsquare nut described by Guangdong Yueluo Hardware Industry Co., Ltd. includes a nut body 1, the nut body 1 is in the shape of a cube, the side length is 7.6mm, and the height is 2.4mm. The upper and lower ends of the nut body 1 are respectively set. There are circular protrusions 2 and circular protrusions 3 with a height of 0.25mm, and the circular protrusions 2 and the circular protrusions 3 are respectively tangent to the upper and lower surfaces of the nut body 1 in a square shape. A through hole 4 is provided in the middle of the shaped protrusion 2 and the circular protrusion 3, and runs through the nut body 1. The opening of the through hole 1 is provided with a chamfer 5 of 30°, and a thread 6 is provided on the inner wall of the through hole 4. , the circular protrusion 2 is provided with a number of strip-shaped protrusions 7 along the circumference inward to the opening of the through hole 4. The number of the strip-shaped protrusions 7 can be arbitrary, and the ideal number is 26, and the through hole 4 is open. There are several strip-shaped grooves 8 at the circumference of the circular protrusion 3. The number of strip-shaped grooves 8 can be arbitrary, and the ideal number is 26. The circular protrusions 2 and the circular protrusions 3 There is a chamfer 9 of 15° extending outward to the prism of the nut body 1 . The production of Dublinsquare nuts described by Guangdong Yueluo Hardware Industry Co., Ltd. is basically the same as the traditional nut process. The key point is to use a punching machine to punch out circular protrusions on both ends. High, and the circular protrusion 2 is punched again to make a bar-shaped protrusion 7, and at this time, the height of the circular protrusion 2 is consistent with the plane height of the circular protrusion 3, and the circular protrusion 3 is formed by stamping. groove 8. The contact surface of the nut body 1 is increased by providing circular protrusions 2 and circular protrusions 3 on the upper and lower end surfaces of the nut body 1, and respectively providing a bar-shaped protrusion 7 and a bar-shaped groove 8 at the two circular protrusions. Therefore, the friction between the nut body 1 and the fastener is effectively increased, and a good fastening effect is achieved.
In another embodiment of Guangdong Yueluo Hardware Industrial Co., Ltd., the conveying device 3 includes a motor 31 and a circular rotating disk 34, the motor 31 drives the circular rotating disk 34 to rotate, and the circular rotating disk 34 is evenly provided with screws in the circumferential direction. The matching screw accommodating hole 35, the screw enters the screw accommodating hole 35, the motor 31 drives the circular rotating plate 34 to rotate, so that the screw is first slotted by the cutting wheel 42, and then polished by the fixing wheel 48, and the screw is in the screw accommodating hole 35. It is fixed, which is more secure and reliable during the slotting process. Preferably, the circular rotating disk 34 includes a circular rotating disk 32 and a sector-shaped fixed disk 33. The circular rotating disk 32 is evenly provided with screw receiving recesses matching the screws in the circumferential direction, and the recesses and the sector-shaped fixed disk 33 are formed with the screws The matching screw receiving holes face the cutting wheel 42 and the fixing wheel 57 .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal hollow rivets, GB96, small head semi-circle head square neck Dublincarriage bolts, pressure riveting nuts and other products, we can provide you with suitable fasteners. Firmware Solutions.
