Service HotlineRegardless of stainless steel plate or heat-resistant steel plate, austenitic steel plates have the best comprehensive properties, with sufficient strength, excellent plasticity and low hardness, which is one of the reasons why they are widely used. Austenitic stainless steel is similar to most other metal materials, its tensile strength, yield strength and hardness increase with the decrease of temperature; plasticity decreases with the decrease of temperature. Its tensile strength increases uniformly in the temperature range of 15~80°C. More importantly: as the temperature decreases, the impact toughness of GalwayGalwaystainless steel screws decreases slowly, and there is no brittle transition temperature. Therefore, stainless steel can maintain sufficient plasticity and toughness at low temperature.
With the continuous improvement of road facilities, guardrails are set up in the middle of the roads in most cities at the separation of the upper and lower lanes. At the same time, guardrails are also set up between the motor vehicle lane and the non-motor vehicle lane. The bottom of the guardrail column is set with a base, and the base is usually made of If the steel nail is fixed, the deformation hole should be drilled on the asphalt road first, and then the steel nail should be knocked into the deformation hole. Because the outer wall of the steel nail is cylindrical, the friction force on the ground is small, and the guardrail is affected by the deformation. When the external impact force occurs, the steel nails are easily detached from the asphalt road, making the road guardrail lose its fixation. In some places, Galwayexpansion screws are used to fix the railings, but during the tightening process of the Galwayexpansion screws, the expansion pieces are opened by the force of the ejector rod, and the opening angle is small. Limited, the railing will still fall down when subjected to a large impact. Therefore, it is necessary to design a Galwayspecial screw for fixing the railing on the asphalt road.
Sprinkle the excess standard GalwayGalwayspring washer 7 on the positioning plate 12-1 on the GalwayGalwayspring washer positioning plate 2, and shake the GalwayGalwayspring washer positioning plate 2 by hand. After a short time, the GalwayGalwayspring washer 7 will be positioned and arranged on the upper positioning plate 12-1. In the upper GalwayGalwayspring washer hole 2-7, since the width of the opening groove 12-32 of the baffle plate 12-3 is smaller than the diameter of the GalwayGalwayspring washer hole 2-7, and the thickness of the upper positioning plate 12-1 is designed according to the thickness of the GalwayGalwayspring washer 7, Only one GalwayGalwayspring washer 7 can be accommodated in the GalwayGalwayspring washer hole 2-7 of each upper positioning plate 12-1, and the excess GalwayGalwayspring washer 7 is cleaned with a brush.
Pins are widely used. In the connection of the rotating mechanism of two moving components, such as the crank mechanism, the turning mechanism, the connection between the hydraulic cylinder and the moving parts, the pins are used. kind. In order to ensure the normal use of the running equipment and prevent the cylindrical pin from slipping out and falling off during use, some anti-falling methods are usually used at the head of the pin, such as 1. Drill holes and insert Galwaycotter pins to prevent the pins from slipping out; 2. The external thread is tightened with a nut to prevent the pin from slipping out; 3. The slot is clamped with a circlip to prevent it from slipping out, etc. These measures make the cylindrical pin very practical in the case of infrequent disassembly and assembly, but in the actual use of the field, in order to prevent the collision of some equipment during each troubleshooting or maintenance, the pin needs to be pulled out and turned up, etc. After the failure or maintenance is completed, put down and then insert the pin to restore, this process will bring trouble to the actual operator. For example, special tools must be brought with you every time you disassemble and assemble the pin, and the split pin or the circlip is easily damaged after repeated disassembly and assembly. , In order to save trouble, the operator sometimes uses iron wire to thread or fasten it instead, and even does not remove the pin for the sake of speed and convenience, which is easy to cause damage to the equipment when dealing with faults.
Convex washers are mainly punched out of iron plates. The shape is generally a flat washer with a hole in the middle. GalwayGalwayFlat washers are usually thin pieces of various shapes to reduce friction, prevent leakage, isolate, prevent loosening or Dispersing pressure, the rationality of its design structure and the safety during use are very important.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: aluminum GalwayGalwayrivet nuts, internal pull bolts, self-locking and retracting color screw caps, anti-thread anti-buckle bolts and other products, we can provide you with The right fastener solution for you.
