Service HotlineNuts and bolts are one of the most widely used fasteners in modern mechanical structures. At present, the common metric bolts and nuts are generally trapezoidal in cross-section. The connection between the bolt and the nut is prone to loosening under severe vibration, or even falls off by itself, and the tightening force of the bolt and nut thread is mainly concentrated in the bolt thread and Between the teeth of the first few threads where the threads of the nut are in contact, resulting in loosening of the fastener and sliding pressure of the threads
When the mold is manufactured, many positioning pins need to be installed to fix the relative position between the two parts. The positioning pins are usually sunk into the positioning pin holes on the mold. Since the mold needs to be pulled out frequently during assembly, in order to Remove the parts and make corrections. At the same time, the mold also needs to pull out the positioning pins during maintenance to remove the damaged parts for maintenance. Therefore, the workload of pulling the pins is large. The existing methods are: 1) When installing the pins, The operator uses a self-made long screw that matches the threaded hole of the pin to screw it into the pin, and then aligns the pin hole with a hammer to hit the screw to make the pin snap in, and then screw the screw out by hand. The disadvantage is: on the one hand, the hammer hits the screw It is easy to cause the screw to be damaged or deformed, and it cannot be used normally. On the other hand, it is labor-intensive to remove the screw by hand and may not be able to be removed; 2) When pulling out the pin, the operator will screw the screw into the pin and use force directly or with pliers To pull out a screw, a few companies use a large pin puller to pull it out. The disadvantage is that it is too laborious and time-consuming to pull out by hand or with pliers. Even if a large pin puller is used, the weight of the pin puller itself is large. , it is inconvenient to use.
Most of the existing screws use an integral metal structure, and there are still some problems, such as large weight, high cost of materials, wear resistance, hardness, rust resistance, corrosion resistance, high and low temperature resistance, brittleness, toughness, etc. Many occasions cannot meet the needs of production, and further improvements are needed to improve production efficiency, reduce costs, improve safety, and prolong the service life of screws.
Basic requirements for the installation of T-bolt sleeve components: only when the T-head and the middle slot of the anchoring plate are in good agreement and the anchoring surfaces are in close contact, can the force be evenly applied. If the T-head and the anchoring plate are in line contact, even only point contact , the bolt is partially stressed, which will seriously affect the life. Therefore, the verticality of the sleeve installation must be less than or equal to 1/1000, that is, the horizontality of the anchoring plate surface must be less than or equal to 1/1000, and the center deviation of the sleeve must be controlled within 5mm (the center deviation of the T-bolt is 2mm). Therefore, improving the embedded accuracy of the T-bolt sleeve is the key to the installation of the T-bolt integral sleeve.
In the installation of the external electrical components of the high-voltage electrical box, generally, the whole aluminum alloy profile with a T-slot is laid on the shell of the high-voltage electrical box, and then the upper nut is placed in the T-slot, and the bottom of the Galwaysquare nut is provided with a spring , When installing the electrical components, align the mounting holes with the screw holes of the Galwaysquare nut, then screw and tighten the screws to achieve the installation of electrical components. The biggest defect in the above installation process is that the alignment of the mounting hole and the screw hole is not very convenient, and the spring at the bottom of the Galwaysquare nut is easy to be missing. Once the spring is missing or damaged, the Galwaysquare nut cannot be effectively positioned in the T-slot. It makes the alignment of the mounting hole and the screw hole more difficult. Third, the above-mentioned connection and fixing method itself is not particularly ideal.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: color zinc with washers and GalwayGalwaytoothed nuts, guardrail anti-theft screws, expansion rivets, plastic flat washers and other products, we can provide you with products suitable for you fastener solutions.
