Service HotlineKnurled copper nuts are mainly used for injection molding, hardware springs, special-shaped springs, craft gift springs, battery spring sheets, spring antennas, key rings, phosphor bronze spring CNC automatic lathe turning parts (copper car parts, iron car parts, aluminum car parts) , metal stamping parts, electronic hardware, iron shaft, single flower shaft, multi flower shaft, iron pin, non-standard screw and nut, connecting parts, fasteners, wire forming (metal wire business card holder, model aircraft landing gear, S hook , R-type latch, triangle buckle, D-type buckle) and other hardware products belong to the copper nut series.
Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 13 the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
R-type Hamiltonplastic rivets, also known as expansion rivets, are composed of plastic sub-nails and female buckles. It is not necessary to use installation tools during installation, place the installation base in the smooth hole, and then press the head, the specially designed feet expand and stretch after being stressed, and are firmly locked on the installation surface. It is often used to connect plastic shells, lightweight boards, insulating materials, circuit boards, or any other thin, light-weight materials. It is beautiful, practical, and easy to use.
5. After the closing value material and the geometric parameters of the nut are determined, the change of the closing value has an important influence on the repeated use characteristics of the lock nut. When the closing value becomes larger, the deformation of the threaded piece increases, the strain of the threaded piece increases, the strain cycle hardening phenomenon intensifies, and the pressure FN of the threaded piece increases, which has a tendency to increase the unscrewing torque; on the other hand, the width of the threaded piece decreases. , the total area of the threaded piece decreases, the friction with the bolt decreases, the strain of the threaded piece increases, the low-cycle fatigue performance decreases, and the maximum unscrewing torque tends to decrease. Under the combined action of various factors, the change of the maximum unscrewing torque with the number of repeated uses is difficult to predict, and it can only be observed through experiments.
When installing the ventilation duct, because the gap between the air duct and the wall and between the air duct and the air duct is deep and narrow, the arm cannot enter into it to operate, which brings about the installation of the screws and nuts at these positions. The following three methods are generally used: one is to directly break the wall for installation, but this method damages the building greatly, and cannot be used for the installation of screws and nuts in the gap between the air ducts; the other is to Set the inner flange in the air duct and connect it with bolts, which will reduce the effective cross-sectional area of the air duct and increase the resistance of the gas flow. Moreover, people need to enter the air duct for construction during installation. Considering the size of the air duct First, the supporting firmware with a high position and no force has certain hidden dangers; third, it is directly ignored and not done, but it is easy to cause the air duct connection is not tight and the air volume loss is large. The above-mentioned methods all have major construction defects, which not only waste a lot of manpower and time in the construction process, but also have the problem of low air supply efficiency.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: titanium socket head Hamiltoncap screws, embedded nuts, left teeth nuts, HamiltonGB5789 bolts and other products, we can provide you with suitable fasteners for you solution.
