Service HotlineAt present, with the continuous growth of the demand for communication products, higher and higher requirements are put forward for the production capacity of equipment manufacturers, and at the same time, the requirements for the cost, weight and reliability of communication products are also more and more stringent. In order to facilitate the positioning of the equipment, pins are often used to complete the equipment, and a certain cost is incurred for its manufacture and assembly. In the past, such parts have been assembled in the form of threads. In order to ensure that the assembly height is within the specified range and to prevent loosening, bar turning is often used to form threads and positioning steps, and thread pinning glue is used in the assembly, and the cost of machining is relatively high. Large, more material waste. Based on the above drawbacks, in order to better solve this problem, some existing manufacturers use the interference fit riveting method, which solves the problem of material waste and anti-loosening, but the inner diameter of the pin hole and the outer diameter of the pin are matched. The machining accuracy of the machine is relatively high. Once the matching size is out of tolerance, a second matching is required, which wastes working hours and increases the slack time.
With the improvement of living standards, people's requirements for the comfort of sitting and bedding are gradually increasing. Independent pocket spring cushions have moderate hardness and are generally welcomed by people.
rivet is a metal rod-shaped part with a cap at one end. During riveting, the rivet uses its own deformation or interference to connect the riveted parts. Commonly used rivets are semi-circular head, flat head, semi-hollow rivets, solid rivets, countersunk head rivets, Hamiltonblind rivets, hollow rivets, etc. At present, rivets are widely used in various backplane products and other stamping products. Since rivets are responsible for the functions of locking, positioning and bearing lateral force in the product, the degree of riveting and vertical have higher requirements. However, in actual production, there are often problems such as the failure of the rivet torsion to meet the requirements, the rivet being skewed by the rivet, the surface of the rivet being cut, the rivet placement being inaccurate and requiring manual repositioning, etc. Very high and very inefficient.
As shown in Figures 1 and 2, Yueluo is an automatic locking screw. From bottom to top, there are screw head 1 with external thread, screw rod and nut 3. The screw rod is a hollow screw rod 2, and the hollow screw There are long holes 7 on both sides of the rod 2, the width of the long hole 7 is smaller than the inner diameter of the hollow screw rod 2, and a spring 4 is arranged in the inner cavity of the hollow screw rod 2, and the spring 4 is not smaller than the hollow screw rod 2 in the free extension state. The upper end of the spring 4 is provided with a plug 5, the distance between the two wings 6 of the plug 5 is greater than the diameter of the nut 3, and the two wings 6 of the plug 5 protrude out of the hollow screw rod 2 through the long hole 7. When using the Yueluo, you only need to compress the spring through the two wings, insert the U-shaped clip after the neutral position is exposed, and then release the two wings, the spring will automatically return and compress the U-shaped clip, which is easy to use, safe and reliable. Claim 7. A self-locking screw, from bottom to top, is a screw head, a screw rod and a nut provided with an external thread, characterized in that the screw rod is a hollow screw rod, and both sides of the hollow screw rod are respectively provided with Long hole, the width of the long hole is smaller than the inner diameter of the hollow screw rod, the inner cavity of the hollow screw rod is provided with a spring, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole.
The main part of the pin screw is an ordinary screw, and the pin can be arranged in the melting section of the screw or the drop groove of the metering section or the smooth cylindrical surface without screw grooves at the end of the metering section. The pins are arranged in a certain arrangement, with varying degrees of density and quantity. HamiltonCylindrical pins are formed by fitting the pins into the holes of the threaded rod; square or diamond-shaped pins are formed by milling directly on the threaded rod. If these pins are set in the melting zone, the pins can break up the solid bed, destroy the two-phase flow, stir the solid and liquid phases together, increase the contact area between the undissolved solid phase fragments and the contained material, and promote molten. If the pin is set in the melt conveying area, its main function is to divide the material flow, increase the interface, change the direction of the material flow, and rearrange the flow beam. Divide and merge multiple times, change the flow direction, and homogenize the melt composition and temperature. The mixing section is an inwardly slotted structure arranged at the end of the common screw homogenizing section, and its outer diameter is equal to the outer diameter of the screw. The grooves are divided into several groups, and each group is the confluence area of the material. The materials are divided by grooves, meet in the confluence area, and then divide and confluence. The principle is similar to the pin type. The characteristic of the separate screw is that in addition to the original screw thread (called the main screw) on the melting section, there is also an additional thread (called an additional thread) whose outer diameter is slightly smaller than the outer diameter of the main thread, and the main and auxiliary threads are With different leads, the secondary thread starts from the end of the feeding section (and connects with the feeding section here), and after several threads, gradually intersects the main thread of the homogenizing section. The screw groove depth and thread lead of this kind of screw change gradually from the beginning of the feeding section to the end of the homogenization, that is, the thread lead gradually narrows from the width, and the groove depth gradually becomes shallower from the depth, which can maximize the compression of the material.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: nut HamiltonHamiltonHamiltonHamiltonset screw flat washer HamiltonHamiltonspring washer combination, external tongue Hamiltonstop washer, hexagon head screw, set full flat washer HamiltonHamiltonspring washer combination and other products, we We can provide you with the right fastener solution for you.
