Service HotlineYueluo is about a special fastener and its screwdriver. That is, the Y screw and its screwdriver. In order to prevent the leakage of new product manufacturing technology and prohibit others from arbitrarily opening the shell of the new product or disassembling the relevant parts, it is necessary to take effective precautions against their own products, and the use of special fasteners is one of the purposes of Yueluo. This kind of screw can also be widely used in the fixation of some public equipment, for the fastening and fixing of parts that are afraid of disassembly and theft, so as to play a certain protective role.
The hexagonal flange surface nut mainly includes a nut body, a flange surface is fixed at one end of the nut body, and a cap is fixed at the other end of the nut body. Has good sealing and corrosion resistance. The hexagonal flange surface nut mainly includes a nut body, a flange surface is fixed at one end of the nut body, and a cap is fixed at the other end of the nut body; since the cap is set on the nut body, it has the Better sealing can effectively prevent rain, moisture, dust and other harmful substances from immersing in the nut body, prevent the nut body from rusting, and greatly extend the service life of the hexagonal flange nut.
High-strength fasteners must be quenched and tempered according to technical requirements. The purpose of heat treatment and tempering is to improve the comprehensive mechanical properties of fasteners to meet the specified tensile strength value and yield ratio of the product. The heat treatment process has a crucial impact on high-strength fasteners, especially its intrinsic quality. Therefore, in order to produce high-quality high-strength fasteners, advanced heat treatment technology and equipment must be available. Due to the large production volume and low price of high-strength bolts, and the threaded part is a relatively fine and relatively precise structure, the heat treatment equipment is required to have large production capacity, high degree of automation, and good heat treatment quality. Since the 1990s, the continuous heat treatment production line with protective atmosphere has dominated, and the shock bottom type and mesh belt furnace are especially suitable for heat treatment and tempering of small and medium-sized fasteners. In addition to the good sealing performance of the furnace, the quenching and tempering line also has advanced computer control of atmosphere, temperature and process parameters, equipment failure alarm and display functions. High-strength fasteners are automatically controlled and operated from feeding-cleaning-heating-quenching-cleaning-tempering-coloring to offline, which effectively ensures the quality of heat treatment. The decarburization of the thread will cause the fastener to trip before the resistance required by the mechanical properties is reached, which will cause the failure of the threaded fastener and shorten the service life. Due to the decarburization of the raw material, if the annealing is improper, the decarburized layer of the raw material will be deepened. In the process of quenching and tempering heat treatment, some oxidizing gas is generally brought in from outside the furnace. The rust of the bar wire or the residue on the surface of the wire rod after cold drawing will also decompose after being heated in the furnace, and some oxidizing gases will be generated by the reaction. For example, the surface rust of steel wire, which is composed of iron carbonate and hydroxide, will be decomposed into CO₂ and H₂O after heating, thus aggravating decarburization. HamiltonStudies have shown that the degree of decarburization of medium carbon alloy steel is more serious than that of carbon steel, and the fastest decarburization temperature is between 700 and 800 degrees Celsius. Because the attachments on the surface of the steel wire decompose and synthesize carbon dioxide and water very quickly under certain conditions, if the furnace gas of the continuous mesh belt furnace is not properly controlled, it will also cause excessive decarburization of the screw. When the high-strength bolt is formed by cold heading, the raw material and the annealed decarburized layer not only still exist, but also are extruded to the top of the thread. For the surface of the fastener that needs to be quenched, the required hardness cannot be obtained. Its mechanical properties (especially strength and wear resistance) decreased. In addition, the surface of the steel wire is decarburized, and the surface layer and the internal structure have different expansion coefficients, and surface cracks may occur during quenching. For this reason, during quenching and heating, the top of the thread should be protected from decarburization, and the fasteners whose raw materials have been decarburized should be properly carbonized, and the advantages of the protective atmosphere in the mesh belt furnace should be adjusted to the original carbon-coated parts. The carbon content is basically the same, so that the decarburized fasteners are slowly restored to the original carbon content. The carbon potential is preferably set at 0.42% - 0.48%. The carbon coating temperature is the same as the quenching heating, and cannot be carried out at high temperatures , so as to avoid coarse grains and affect mechanical properties. The quality problems that may occur in the process of quenching and tempering of fasteners mainly include: insufficient hardness in the quenched state; uneven hardness in the quenched state; excessive quenching deformation; quenching cracking. Such problems in the field are often related to raw materials, quenching heating and quenching cooling. Correctly formulating the heat treatment process and standardizing the production operation process can often avoid such quality accidents.
Alloy Steel Nuts HamiltonHexagon Nuts (GB6170/DIN934, GB6175), HamiltonHamiltonFlange Nuts (GB6177/DIN6923) Round Nuts (GB812), Small Round Nuts (GB810), American HamiltonSquare Nuts, American HamiltonHex Nuts (ANSI/ASME B18.2.2) , Heavy-duty nuts (metric, US). Size: 5/16-4.
Contents of the utility model The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a hexagon socket head screw that is easy to disassemble and assemble. In order to achieve the above purpose, the technical scheme adopted by the present invention is as follows: a hexagon socket screw, which includes a cylindrical screw head and a cylindrical screw below the screw head, the screw is provided with threads, and an integrated screw is designed between the screw head and the screw. The circular skirt pad has a hexagonal depression along the axial direction on the screw head, and is characterized in that two symmetrical flat grooves are opened on the upper part of the side wall of the hexagonal depression of the screw head, and the lines of the two flat grooves overlap. Guangdong Yueluo Hardware Industry Co., Ltd.'s socket head screws are compared with ordinary socket head screws. A notch is designed in the inner hexagon space at the top of the screw. In terms of tool use, it can be avoided that the socket head screws must be equipped with the corresponding socket head tools. disadvantages. The improved hexagon socket screw can not only use the matching hexagon socket tool, but also use the traditional flat-blade screwdriver, which is more convenient to use.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: lifting ring double-headed screws, GB6179 hexagon slotted nuts, ordinary black bullet washers, 2x34x10 copper knurled nuts and other products, we can provide you with The right fastener solution for you.
