Service HotlineAt the beginning of the quality inspection process broadcast, we ordered the cross recessed screw and screw wire material into our production screw industry. For manufacturers in the screw industry, we must first detect the wire diameter of the screw wire and the material of the screw. Generally, the wire diameter of the screw is measured by a caliper and a measuring wire. Diameter size, whether it is the same as the size ordered by yourself. After testing these, it is the testing in the production process, starting from the head of the screw, to determine the size of the head, the opposite side of the head, the diagonal angle, the depth of the cross groove, the tolerance range of the screw, and so on. These are checked with calipers. In the inspection of all aspects when rolling teeth, the main thing is whether the thread can pass the pass and stop gauge, and whether the screw thread can pass the gauge and stop. Next is the electroplating measurement problem. After electroplating, whether it meets the requirements of environmental protection and whether it can pass the time required by the salt spray. Tools include environmental testing machines and salt spray testing machines. In short, in the production and sales process of cross recessed screws, there must be necessary tools to detect the quality of screws. The summary should be summarized as follows: calipers, hardness testers, salt spray machines, environmental testing machines, pass and stop gauges, etc. .
screw suitable for a variety of tools is a single-structure threaded part, including a screw body and a screw head. The outer surface of the screw body is processed with an external thread 1, and the outer side of the screw head is formed by six screw heads. Prismatic, the top surface of each edge of the outer hexagonal prism is a boss, between each boss is an end face groove 4, and the middle of each boss is provided with an end face hole 3; the inner side of the screw head is formed by six screw heads. The side surface 5 forms an inner hexagonal prism hole, and the bottom of the inner hexagonal prism hole is processed with a cross groove 13 .
In the existing production technology, such as construction machinery, double nuts are often used to fasten the workpiece. With the long-term vibration in the working environment, there is a thread gap between the nut and the bolt, and there is no self-assembly between the nut and the bolt. Locking action, the relative displacement between the nut and the bolt will occur under the action of vibration, resulting in the loosening of the nut and the bolt and the loss of the tightening effect.
The semicircular key is a kind of key, the upper surface is a plane, the lower surface is a semicircular arc surface, the two sides are parallel, commonly known as the crescent key. It is basically the same as the flat key connection method, but it is more convenient to manufacture and disassemble than the flat key, and is especially suitable for the connection between the tapered shaft and the hub. The half-round key transmits torque on the side, but the keyway is deep, which weakens the shaft greatly. Due to the deep keyway, the bottom of the keyway is easily deformed after the shaft is heat treated. Therefore, when the semicircular key and the keyway are assembled in a transitional fit relationship, the interference between the lower part of the semicircular key and the bottom of the keyway often occurs, resulting in difficult or impossible assembly. Assembly situation. In order to solve the above technical problems, the current method is to make the thickness of the semicircular key appropriately thin, so that the semicircular key and the keyway are clearance fit, which brings about a large gap between the upper part of the semicircular key and the keyway, and the semicircular key is in operation. Difficult to locate in the keyway, affecting smooth transmission.
At present, the washing machines used in the domestic market, especially the large-capacity washing machines, have high rotational inertia due to their large washing capacity. The wear between the input shaft and the clutch sleeve will cause the increase of the axial clearance. There will be strong shaking and loud noise, which will increase the wear and tear and affect the service life. In the prior art, the wave washer is used to prevent loosening and buffer shock, so that the gap between the input shaft and the clutch sleeve will not increase due to the wear of the two, which plays the role of automatic gap compensation, so as to ensure the clutch Smooth rotation, low noise and light wear ensure the reliable service life of the clutch.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB91 spring Los Angelescotter pins, national standard metric bolts, HPC Los AngelesLos Angelesstainless steel screws, extended cylindrical knurled nuts and other products, we can provide you with suitable tightening. Firmware Solutions.
