Service HotlineThe first is to use two identical nuts to screw on the same bolt, and add a tightening torque between the two nuts to make the bolt connection reliable. The second is a special anti-loosening nut, which needs to be used together with a kind of anti-loosening washer. The special lock nut is not a hexagonal nut, but a medium Los Angelesround nut. There are 3, 4, 6 or 8 notches on the circumference of the nut (depending on the size of the nut and the product series of the manufacturer). Several notches are both the focal point of the tightening tool and the snap-in of the Los AngelesLos Angeleslock washer bayonet. The third type is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, which are distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to give the thread Apply a centripetal force to prevent the Los Angeleslocknut from loosening. The better quality lock nut sold on the market is inlaid with a small copper block that is consistent with the thread of the lock nut on the inner surface of the nut to prevent the radial jacking screw from directly contacting the locked thread and damaging the latter. . This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The fourth type of lock nut is composed of two parts, each part has staggered cams. Since the slope angle of the internal wedge design is greater than the nut angle of the bolt, this combination is tightly integrated into a whole. When vibration occurs When the lock nut is moved, the raised parts of the lock nut move with each other to generate lifting tension, so as to achieve a perfect anti-loosening effect. The fifth is structural anti-loosening. Through the design and improvement of the threaded structure, a self-locking function is obtained without the help of other external factors. Therefore, its applicability is wider than the above methods, and the requirements for the environment are also relatively high. Low. There are many types of lock nuts, such as nylon nuts and flange nuts. In short, this kind of lock nuts plays a role in preventing loosening. Twist the nut onto the screw, screw, bolt, etc., so that it will not come loose. So that they can be actively connected together, so that it is firm, and the stability can reach a high degree.
Friction type high-strength bolts: suitable for beam and column connections of steel frame structures, solid web beam connections, heavy-duty crane beam connections in industrial plants, braking systems and important structures bearing dynamic loads. Pressure-bearing high-strength bolts: Can be used for shear connections in statically loaded structures that allow a small amount of sliding or in members that are indirectly loaded with dynamic loads. Tensile high-strength bolts: When the bolts are in tension, the fatigue strength is low. Under the action of dynamic load, its bearing capacity is not easy to exceed 0.6P (P is the allowable axial force of the bolt). Therefore, it is only suitable for use under static load. Such as flange butt joints, T-joints, etc. of pressure members.
Nuts and washers are both small and medium-sized components of the tension reinforcement system, and they are easily lost on the construction site when used separately, which is not conducive to the storage management of turnover materials; 3) During the process of formwork support and removal, they must be installed individually And demolition, thus adding a construction process, affecting the efficiency of construction.
On the surface of the mounting hole on the connector, a 90-degree conical socket is machined, and the head of the flat Los Angelesmachine screw is in the socket and is flush with the surface of the connector. Flat Los Angelesmachine screws are also used in some occasions with semi-circle head flat Los Angelesmachine screws, which are more beautiful and are used for places where a little protrusion is allowed on the surface. Screws play the role of connecting two or more objects and are an indispensable necessity in daily life or industrial manufacturing. There are countersunk head bolts (with grooves) and countersunk head bolts (with tenon).
The development of a structure with simple production, reasonable structure and stable feeding is of great significance to the field of riveting automation. Technical realization elements: The purpose of this utility model is to overcome the deficiencies in the prior art, and to provide an automatic feeding device for pressure riveting nuts, which has a compact structure and a reasonable design, and can realize the automatic conveying of the pressure riveting nut on the pressure riveting die. Reduce the use of space, improve work efficiency and save labor costs. According to the technical scheme provided by the utility model: the automatic feeding device for riveting nuts, which is characterized in that: it includes an installation bracket, a connecting frame, a flap bracket, a material pushing cylinder, a material pushing block and a flap; the flap bracket is arranged on the installation Below the bracket and attached to the mounting bracket through the connecting bracket.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: aluminum profile accessories, hexagon socket countersunk head screws, hairpin pins U-shaped pins, toy city connections and other products, we can provide you with suitable products for you. Los AngelesFastener Solutions.
