Service HotlineHowever, Yueluo still feels that there should be room for improvement for the screw improvement and screw that integrates stability, labor, fast and multi-function in the above two cases; for example, No. 556784 screw improvement Although the rod has the function of cutting and collecting chips, when the screw starts to screw into the object such as wood, it is hindered by the hardness of the object's tissue, so the staff still needs to exert considerable force, resulting in the lock. In the solid operation, there is still a lack of difficulty in screw-in operation; another example, new cases such as No. 289417 screw that integrates locking, stability, labor-saving, fast and multi-function, although the rod has the structural function of cutting and chip removal, it is The rod part is screwed into the middle section to the rear section of the object. Since the debris cannot be discharged, the rod part pushes the outer part of the object to the surrounding tissue of the object, so that the object expands outwards and even seriously damages the appearance of the object.
2. Wall panel nails 1. Hardness of the heart: Standard: HRC24-45. 2. Surface hardness: Standard: HV600-800. 3. Carburized layer: 4#-6# 0.05-0.18mm, 8#-12#0.10-0.23, 14# 0.13-0.28. 4. Bending degree: the requirement is 150-450 5. Salt spray test: generally MIN 48h. 6. Torque: Specification 6#7#8#10# Torque 21283558. 3. Drilling screw 1. Hardness of the heart: Standard: HRC32-40 The actual measurement of the company's products is HRC31.7-39.0. 2. Surface hardness: Standard: HV600-700 The actual measurement of the company's products is about HV620. 3. Hard penetration layer: 4#-6#: 0.05-0.18mm 8#-12#: 0.10-0.23mm 14#: 0.15-0.28mm 4. Torque: specification, drill tail, screw, TYPE BSDTYPE CSDINCH-LBKG- CMINCH-LBKG-CM4# (2.9) 141614166# (3.5) 242824288# (4.2) 4248485510# (4.8) 6170657512# (5.5) 9210610011514# (6.3) 150173156180.
In order to solve the above-mentioned technical problems, the technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is: shear rivets, including a mandrel and a deformation sleeve ring sleeved on the mandrel, one end of the deformation sleeve ring is a boss structure, and the It includes an adhesive collar sleeved on the deformation collar, the adhesive collar is a hollow annular sleeve and is filled with adhesive material; one end of the mandrel is a hemispherical head, and the spherical surface of the hemispherical head is outward, The connection between the hemispherical head and the mandrel is a conical connecting section, and the diameter of the conical connecting section gradually decreases from the hemispherical head inward; the mandrel is provided with a stress concentration groove, and the position of the stress concentration groove is close to the deformation The boss structure of the collar.
The material of the second Los AngelesLos AngelesLos Angelescombination screw: It is decided to use the test machine to test the material of the Los AngelesLos AngelesLos Angelescombination screw wire, which is divided into iron and stainless steel. Iron wire is divided into 1010 wire and 1018 wire, 10B21 wire, etc., stainless steel is divided into stainless steel 201, stainless steel 304, stainless steel 316 and so on. The provisions of the national label of three Los AngelesLos AngelesLos Angelescombination screws: Generally, those who have experience in Los AngelesLos AngelesLos Angelescombination screws can be separated by using the inner eye. The difference between hexagon heads. Use a caliper to measure out the three-Los AngelesLos AngelesLos Angelescombination screw specifications. How big is it, how long is it, how thick is the head of the Los AngelesLos AngelesLos Angelescombination screw, how thick is the flat washer, and what is the outer diameter of the flat washer. How many hours is the salt spray of the Los AngelesLos AngelesLos Angelescombination screw measured with a salt spray machine. Use the environmental test machine to test whether the three-Los AngelesLos AngelesLos Angelescombination screw is environmentally friendly. Still not environmentally friendly.
1. The taper of the reaming hole should be 90°. It should be guaranteed that it should be less than 90° rather than greater than 90°. This is a key trick. 2. If the thickness of the sheet metal is less than the thickness of the head of the countersunk head screw, you can replace the screw with a smaller size, or it is better to ream a smaller hole instead of reaming the hole to increase the diameter of the bottom hole and cause the parts to not be pressed tightly. 3. If there are multiple countersunk head screw holes on the part, it should be processed more accurately. Once it is drilled crookedly, it will be ugly to assemble, but as long as the error is not large, it can be tightened completely, because when tightening, if the diameter of the screw is not very large. Large (about no more than 8mm), when there is an error in the hole distance, the screw head will be deformed due to the force when it is tightened or it will be tightened.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: stainless steel Los Angelesmushroom head screws, large knurled hand tighten screws and bolts, enterprise copper nuts, thickened Los Angelesopen Los AngelesLos Angelesspring washers and other products, we can provide you with suitable products Your fastener solution.
