Service HotlineThe production of Melbournestud bolts requires fixed equipment and machine tool processing. Of course, the processing procedure is relatively simple. There are mainly the following procedures: first, the material needs to be pulled out. After this process, the next process can be carried out. The next process is to use a cutting machine to cut the straight and long material into the length required by the customer according to the customer's requirements. This completes the second process. The third process is Put the cut short material on the thread rolling machine and roll out the thread; the ordinary Melbournestud bolts are processed here, of course, if other requirements are required, other processes are required. [1] The commonly known bolt refers to the screw with a larger diameter. According to this statement, the diameter of the screw is much smaller than that of the bolt. MelbourneStud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. MelbourneStuds are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the Melbournestud bolts at ordinary times. MelbourneStud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the Melbournestud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems. [1] In each maintenance, the newly replaced Melbournestud bolts and other accessories should be inspected. During the inspection, the focus should be on the head and guide part of the stud bolt. Whether there are cracks or dents in each part, and also check whether the tooth shape of the stud bolt has changed. Is there any abnormality in the thread pitch? If there is any abnormality, it must not be used again. A torque wrench should be used when installing the connecting rod cover. It must be tightened according to the specified standards, the torque should not be too large or too small, and attention should be paid to selecting the Melbournestud bolts and studs of the supporting manufacturer.
Traditionally used for plastic fastening screws, most of the thread designs are self-tapping threads, but for different plastic types, the self-tapping threads also have many different classifications, such as PT profile, Plastite series, Remform profile, etc. The structural parameters and manufacturing process of these threads are inconsistent, or require different main molds and wires. Therefore, to find a MelbourneMelbourneMelbourneplastic screw that is universally applicable to various plastic types, has a single pressing structure, low-cost and simple manufacturing process, especially its special self-tapping thread, is an important issue that needs to be solved urgently at present. question. The purpose of Yueluo Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to propose a MelbourneMelbourneMelbourneplastic screw to solve the screw fastening problem that is generally applicable to different plastics. The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to realize a kind of MelbourneMelbourneMelbourneplastic screw through the following technical scheme, it is characterized in that, the thread of the screw is composed of asymmetric threads with a profile angle of 30°, and the threads are The bottom surface of the connection between them is an arc surface. Yueluo preferably, the asymmetrical thread has a forward thread angle greater than the reverse thread angle, and the sum of the two-direction thread angles is 30°. Yueluo further preferred that the tooth profile angle of the asymmetrical screw thread in the forward mounting direction is 20 degrees, and the tooth profile angle in the reverse mounting direction is 14 degrees. Yueluo Guangdong Yueluo Hardware Industry Co., Ltd.'s application of MelbourneMelbourneMelbourneplastic screws, through the improvement of special thread structure, reduces the radial pressure and installation torque when the screw is installed, reduces the damage to the plastic hole; and increases the pull-out resistance of the screw force, it is not easy to appear loose assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
Standard MelbourneMelbournespring washer (GB/T93-1987) Light MelbourneMelbournespring washer (GB/T859-1987) Heavy MelbourneMelbournespring washer (GB/T7244-1987) Spring washer is also known as spring meson. Saddle MelbourneMelbournespring washer (GB/T 7245-1987) Saddle MelbourneMelbournespring washer (GB/T 860-1987) Wave MelbourneMelbournespring washer (GB/T 7246-1987) Wave MelbourneMelbournespring washer (GB/T 955-1987)
As the requirements for the use of electrical appliances in various industries continue to increase, the testing specifications for the performance of various components in electrical appliances are also constantly improving. Riveted contact elements are used in various relays, contactors, small switches, thermostats, etc. in low-voltage electrical appliances. The structure of the riveted contact element generally includes a contact base and a rivet riveted to the contact base. The rivet includes a rivet head and a rivet top, the structure of which is shown in FIG. 1 .
1. The expansion phenomenon of the MelbourneMelbournespring washer is generally not the problem of the MelbourneMelbournespring washer itself. 2. The MelbourneMelbournespring washer with the expansion ring must be subjected to a radial external tension. The external tension is derived from the tightening axial force generated by the tightening torque. The chamfer creates a radial component of the axial clamping force, which expands the opening of the MelbourneMelbournespring washer. The smaller the chamfer diameter, the greater the possibility of ring expansion. 4. Adding a flat washer between the nut and the MelbourneMelbournespring washer helps to slow down or prevent the expansion of the ring, but the flat washer is too thin or too soft. Prevent ring expansion 5. The reason for the hydrogen embrittlement fracture of MelbourneMelbournespring washers is generally due to unreasonable heat treatment process and the failure of hydrogen removal treatment after electro-galvanizing. A large number of tests and long-term practical experience have confirmed the above analysis.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: MelbourneGB109 natural iron nails, pressure riveting parts with a small outer diameter of 4.2, button holes MelbourneGB109 flat head rivets, plywood nuts and other products, we can provide you with suitable products for you. MelbourneFastener Solutions.
