Service HotlineThe screw refers to the screw (foreign name: Screw), which is a tool that uses the physical and mathematical principles of the oblique circular rotation of the object and the frictional force to gradually fasten the utensils and parts. A screw is a common term for fasteners, an everyday colloquial language. Metric threads are measured in MM (millimeters) and have a cusp angle of 60 degrees. Both US and Imperial threads are measured in inches. The cusp angle of the American thread is also 60 degrees, while the cusp angle of the imperial thread is 55 degrees.
The diameter, length and quantity of the Montrealstud bolts shall meet the requirements, and the type and material of the Montrealstud bolts shall be determined by the grade. There are two types of commonly used Montrealstud bolts (also known as full-threaded studs). The thread is divided into two types: coarse thread and fine thread. The coarse thread ordinary thread is expressed by M and the nominal diameter, and the fine thread ordinary thread is expressed by M and the nominal diameter × pitch. The fastener standard stipulates that M36 bolts use coarse thread, M36 and above diameters can use fine thread, and the pitch is 3. bm=1d studs are generally used for the connection between two steel connected parts; bm=1.25d and bm=1.5d studs are generally used between cast iron connected parts and steel connected parts The connection between the two; bm=2d double-ended stud is generally used for the connection between the aluminum alloy to be connected and the steel to be connected. The former connector has internal threaded holes, and the latter connector has through holes. The threads at both ends of the equal-length studs need to be matched with nuts and washers, and are used for two connected parts with through holes. One end of the welding stud is welded on the surface of the connected piece, and the other end (threaded end) passes through the connected piece with a through hole, and then the washer is put on, and the nut is screwed on, so that the two connected pieces are connected as a whole.
The technical scheme adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is: a pin pressure riveting structure, including a pin, a cavity and a pressure riveting fixture, the pin is a columnar structure, an annular groove is arranged on the surface of the pin, and the cavity is The body is provided with a light hole, the depth of the light hole is greater than the height of the annular groove relative to the bottom of the pin, the lower end of the pin is inserted into the light hole, the pressure riveting fixture includes a pressure riveting part and a pressure-bearing part located on the top of the pressure riveting part, so The riveting part and the pressure-bearing part are provided with coaxial and penetrating connecting holes, and the upper ends of the pins are sleeved in the connecting holes.
MontrealAnchor bolts are also known as stiffened anchor plate anchor bolts, welded anchor bolts, anchor claw anchor bolts, rib plate anchor bolts, anchor bolts, anchor screws, anchor wires, etc. It is specially designed to be buried in the concrete foundation and used as the base for fixing various machines and equipment. Figure 7 anchor bolts are the most commonly used anchor bolts. It is generally made of Q235 steel, with high strength using Q345B or 16Mn material, and also using 40Cr material to process 8.8-strength products, and occasionally using secondary or tertiary rebar. MontrealAnchor bolts are divided into wool, thick rod and thin rod. The wool material is the raw material steel, which is directly processed from round steel or wire without modification; thick rods or called A-type, thin rods or B-type, are processed from steel modified into the corresponding required rod diameter. Welded anchor bolts are made of single-headed bolts welded with stiffened iron plates. Its anti-pulling ability is strong. According to the different conditions of use, it can reach 3.6, 4.8, 6.8, 8.8 and other grades respectively. The tensile capacity of 3.6 grade 7-shaped anchor bolts is the tensile capacity of the steel itself. The tensile strength of anchor bolts directly processed from Q345B or 16Mn raw materials can reach a tensile strength of 5.8. The tensile strength of grades 4.8, 5.8, 6.8 and 8.8 refer to the provisions on mechanical properties in GB/T3098.1.
A kind of nut provided by Yueluo. The nut is in the shape of a casing and is provided with a threaded section. The hole walls at both ends of the threaded section are respectively provided with an annular shape and two grooves, and the notch of the groove points to the hole core. The hole diameter at the notch of the annular groove at the front end of the screw-in direction is larger than the nominal size of the thread segment, and the hole diameter at the notch of the annular groove at the rear end of the screw-in direction is smaller than the nominal size of the thread segment.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: all-metal lock nuts, extended ring screws, GB/T61701 hexagon nuts, MontrealGB6173 flat nuts and other products, we can help you Provide the right fastener solution for you.
