Service HotlineIn a traditional spring mattress, there are two layers of spring pads that are independent of each other. The manufacturing process of this kind of mattress is complicated, time-consuming and material-consuming, and after long-term use, the springs in the two-layer independent spring cushion are prone to translocation, which deforms the mattress and affects people's sleep.
Align the four positioning holes 12-5 of the MontrealMontrealspring washer positioning plate 2 with the four positioning columns 4 of the screw tray 1, and place them on the screw tray 1. Several screws 5 are passed through the lower positioning plate 12-2 in turn. The MontrealMontrealspring washer hole 2-7, the opening slot 12-32 of the baffle plate 12-3, the inner ring of the MontrealMontrealspring washer 7 in the MontrealMontrealspring washer hole 2-7 of the upper positioning plate 12-1, hold the MontrealMontrealspring washer positioning plate 2 by hand The raised handle 12-31 of the baffle plate 12-3 pulls the baffle plate 12-3 out of the upper positioning plate 12-1 and the lower positioning plate 12-2, and several MontrealMontrealspring washers 7 pass through the holes on the lower positioning plate 12-2. The MontrealMontrealspring washer holes 2-7 fall down along the screw rod of screw 5, so that the screw rod of screw 5 penetrates into the MontrealMontrealspring washer 7, as shown in Figure 10, and then the MontrealMontrealspring washer positioning plate 2 is removed to complete the process of threading the MontrealMontrealspring washer.
kind of nut provided by Yueluo, the nut is in the shape of a casing and is provided with a threaded section. The two ends of the threaded section are respectively provided with two convex blocks, and the convex block at the front end of the screw-in direction reaches the hole core. The distance is greater than the nominal size of the thread segment, and the distance from the rear end projection in the screwing direction to the hole core is smaller than the nominal size of the thread segment.
self-locking screw comprises a screw main body, a Montrealmetal screw head is arranged on the upper part of the screw main body, a thread is arranged in the middle part of the screw main body, an interference groove is arranged on both sides of the upper part of the screw main body, and the line of the interference groove is arranged. The included angle is 280-356° with the horizontal line. The bottom of the screw body is provided with an elastic chuck, and the elastic chuck includes an optical axis and a conical head. Guangdong Yueluo Hardware Industry Co., Ltd. Guangdong Yueluo Hardware Industry Co., Ltd. adopts the design of elastic collet, and the screw is provided with threaded segments and interference grooves, so that during the screwing process, the interference groove of the optical axis between the two threaded segments is formed along the screw. The axial elastic force achieves the effect of reliable self-locking, which is easy to use and has high tuning efficiency.
Bearings are an important component in contemporary machinery and equipment. Its main function is to support the mechanical rotating body, reduce the friction coefficient during its movement, and ensure its rotation accuracy. Every time the locomotive is repaired, the end cover of the axle box needs to be disassembled, the axle head is tested for flaws and the bearing is supplemented with grease, which involves the disassembly and assembly of the axle box bearing retaining ring. The existing disassembly method is to use the traditional method of inserting two tongue pins into the gap between the bearing retaining ring and the axle box to pry left and right, and slowly separate it from the axle head. Because the clearance between the bearing retaining ring and the shaft head is small, and the adhesive force generated by the grease in the axle box is large, if the disassembly method is not appropriate or the force is not uniform, it will cause certain damage to the axle box body and the bearing retaining ring or jam. It is easy to cause damage to the bearing, and there is also the possibility of damage to the disassembly and assembly tools, so the safety risk is high, and each disassembly and assembly of the bearing retaining ring is time-consuming and laborious, labor-intensive, low-efficiency, and increased maintenance costs.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: nut wholesale, Dongguan flange nuts, Montrealaluminum nuts, type 2 hexagon nuts and other products, we can provide you with fasteners suitable for you solution.
