Service HotlineType 1) Slotted ordinary screws are mostly used for the connection of smaller parts. It has pan head screws, cylinder head screws, countersunk head screws and countersunk head screws. The head strength of pan head screws and cylinder head screws is high, and they are connected to common parts; the head of semi-countersunk head screws is arc-shaped, and its top is slightly exposed after installation, and it is beautiful and smooth. It is generally used for instruments or Precision machinery; countersunk head screws are used where the nail head is not allowed to be exposed. 2) The head of the hexagon socket head Montrealcap screw and the hexagon socket head flower screw can be embedded in the component, which can apply a large torque and have a high connection strength, which can replace the hexagonal bolt. It is often used in joints where compact structure and smooth appearance are required. 3) Cross recessed ordinary screws have similar functions to slotted ordinary screws, and can be replaced by each other, but the cross recessed ordinary screws have higher groove strength, are not easy to be bald, and have a more beautiful appearance. When using it, it must be loaded and unloaded with the matching cross-shaped screwdriver. 4) Lifting ring screw Lifting ring screw is a kind of hardware accessories for load-bearing during installation and transportation. When in use, the screw must be screwed in to the position where the supporting surface is tightly fitted, and tools are not allowed to be tightened, nor is a load perpendicular to the plane of the lifting ring allowed to act on it. 5) Set screws Set screws are used to fix the relative position of the parts. Screw the MontrealMontrealMontrealMontrealset screw into the screw hole of the part to be fastened, and press its end against the surface of the other part, that is, to fix the former part on the latter part. Set screws are usually made of steel or stainless steel, and their end shapes are conical, concave, flat, cylindrical and stepped. The end of the tapered or concave Montrealend MontrealMontrealMontrealMontrealset screw directly presses the parts, and is generally used in places that are not often disassembled after installation; the end of the flat Montrealend MontrealMontrealMontrealMontrealset screw is smooth and does not damage the surface of the parts after tightening, and is used for frequent adjustment of the position. At the connection, only a small load can be transmitted; the cylindrical end fixing screw is used in the fixed position that needs to be adjusted frequently, it can withstand a large load, but the anti-loosening performance is poor, and anti-loosening measures should be taken when fixing; Set screws are suitable for fixing parts with thicker walls. 6) MontrealSelf-tapping screws When self-tapping screws are used on the connected parts, threads may not be pre-made at the connected parts. Use the screw to tap the thread directly when connecting. It is often used to join thin metal plates. There are two types of taper end tapping screws and flat end tapping screws. 7) Self-tapping locking screw Self-tapping locking screw not only has self-tapping effect, but also has low screw-in torque and high locking performance. Its thread is a triangular section, and the surface of the screw is hardened and has high hardness. Its thread specifications are M2 ~ M12.
The grooved embedded parts are pre-embedded in concrete, and then placed in the groove with MontrealT-bolts. After adjusting the fixed position, the fixed object is locked with a nut to achieve the fixing effect. When the grooved embedded parts are embedded vertically in the concrete or at a certain angle to the horizontal line, the MontrealT-bolts are likely to move in position before they are tightened. In particular, when fixing heavy equipment, multiple MontrealT-bolts are required, and multiple groups of workers are required to help and positioning is difficult, and the installation process is complicated.
The drawing process has two purposes, one is to modify the size of the raw materials; the other is to obtain basic mechanical properties of the fasteners through deformation and strengthening. For medium carbon steel, medium carbon alloy steel also has another purpose, that is, to make the wire rod. The flaky cementite obtained after controlled cooling is cracked as much as possible during the drawing process to prepare for the subsequent spheroidization (softening) annealing to obtain granular cementite. However, some manufacturers arbitrarily reduce the drawing in order to reduce costs. The excessive reduction rate increases the work hardening tendency of the wire rod, which directly affects the cold heading performance of the wire rod. If the distribution of the reduction ratio of each pass is not appropriate, it will also cause torsional cracks in the wire rod during the drawing process. In addition, if the lubrication is not good during the drawing process, it can also cause regular transverse cracks in the cold drawn wire rod. The tangential direction of the wire rod and the wire drawing die is not concentric at the same time when the wire rod is rolled out of the die, which will cause the wear of the unilateral hole pattern of the wire drawing die to aggravate, make the inner hole out of round, and cause uneven drawing deformation in the circumferential direction of the wire. The roundness of the steel wire is out of tolerance, and the cross-sectional stress of the steel wire is not uniform during the cold heading process, which affects the cold heading pass rate. During the drawing process of the wire rod, the excessive surface reduction ratio will deteriorate the surface quality of the steel wire, while the too low surface reduction ratio is not conducive to the crushing of the flaky cementite, and it is difficult to obtain as much granular cementite as possible. , that is, the spheroidization rate of cementite is low, which is extremely unfavorable to the cold heading performance of the steel wire. For the bar and wire rod produced by the drawing method, the partial surface reduction rate is directly controlled within the range of 10%-15%.
The Chinese Patent Application No. 201320368989.2 discloses a pin, which includes a pin body and a cylindrical body part integrally provided with the pin body, a convex tip is provided on the cylindrical body part at one end of the pin body, and the convex The tip is horizontally arranged around the cylindrical body part and protrudes from the surface of the cylindrical body part. The connection between the cylindrical body part and the convex tip is provided with an inclined plane. Although this pin solves the problems of easy loosening and falling off to a certain extent, However, this kind of pin still has the problem of loosening and falling off in the case of bad working conditions and severe vibration.
As a special kind of rivet parts, the rivets for shrinking brake pads are used in the accessories of the automobile industry. The original brake pad rivets do not have a chamfered structure, so the materials cannot be normally fed during assembly, or there are burrs, which lead to unqualified batches. When improving this structure, many manufacturers in the same industry often solve the problem by machining chamfering, but for brake pad rivets with thin thickness, it is impossible to achieve the problem of beating and bad material after chamfering processing.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: chassis copper column isolation column nuts, percussion flat cap Liuding Montrealblind rivets, furniture link nuts, high flat head MontrealMontrealknurled screws and other products. We can provide you with the right fastener solution for you.
