Service HotlineOn the other hand, especially in the aerospace field, the requirements for the sealing effect of screws are extremely strict, and the traditional screws are directly tightened when screwed into the workpiece or equipment, and the sealing effect is determined by the tightness, but due to the machining error of the workpiece or equipment The direct butt seal between the seals is difficult to achieve.
In the prior art, the screw suction device can be implemented in the following two ways. One is to use a magnet to magnetize the electric bit head, and the electric bit head is used to approach the screw, and the screw is stuck by the electric bit head, so that the function of picking up the screw can be realized; The vacuum generator is used to form a negative pressure in the screw guide groove, and the screw is sucked into the tube to realize the screw pickup. The disadvantage of this solution is that in the process of picking up the screws, the grooves of the screws cannot be aligned, which leads to the deviation or leakage of the screws. The disadvantage of this solution is that the screw with an aspect ratio of less than 1.5 is prone to suction and skew, and the stability is not high. It can be seen that the existing technology still needs to be improved and developed.
At present, machinery and equipment have gradually become the main force of work production. Many equipment require frequent maintenance and even replacement of parts during use. During the process of maintenance and replacement, it is inevitable to encounter the problem of screw disassembly and assembly. In the process of disassembly and assembly, it is almost necessary to cooperate with both hands, or because the thread is too long, installation and disassembly are very cumbersome. Especially in the butt installation of flanges, bolts and nuts are used for clamping and fixing at this stage. During use, two hands are required to hold a board, a fixed screw, and a screw nut. This is to prevent the nut from During the turning process, the screw also rotates. When screwing, the wrench should be taken down without interruption, re-selected a good position, and then screw the screw forcefully again, and repeated several times before the screw can be unscrewed. Time and labor costs for maintenance are wasted. At present, there is no screw that is easy to install and remove.
The flat key is a key that relies on the two sides as the working surface and transmits the torque by the extrusion of the key and the side of the keyway, and is mostly installed on the shaft. If the flat key is used for a long time or is in a bad working environment for a long time, dust, oil, etc. will inevitably be stuck between the flat key and the keyway. Since the flat key has no ejector threaded hole for disassembly, it is difficult to dismantle, and during the disassembly process A little carelessness will cause damage to the flat key.
Below in conjunction with the accompanying drawings, Guangdong Yueluo Hardware Industry Co., Ltd. is described in further detail. Please refer to FIG. 2 and FIG. 3, a locking nut includes a nut 1, the bottom is circular, the middle is hexagonal, the top is circular, there is a bolt hole in the center, and the side wall of the bolt hole is threaded. A number of flattening notches 2 are arranged on the top of the nut. According to the locking nut of the preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the number of the flattening notches 2 is three. Due to the above features, the three flattening gaps can be used as the focal point of the tightening tool and the clamping place of the anti-loose gasket bayonet, and the structure is simple and can be formed by die stamping at one time. The above disclosure is only a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., and does not limit itself. Any person skilled in the art, without violating the spirit of the present invention, can think of changes that fall within the scope of It is within the protection scope of Guangdong Yueluo Hardware Industry Co., Ltd.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: MontrealGB867 Montrealround head rivets, 304 flange cross hexagon screws, threaded cylindrical pins, 550 pure titanium pan head screws and other products, we can provide you with The right fastener solution for you.
