Service HotlineThe MontrealMontrealspring washer can prevent loosening and increase the pre-tightening force, while the flat washer does not have this function. It can be used to increase the tightening contact area, prevent the friction between the bolt and the workpiece, and protect the surface of the connector to prevent bolts. The surface of the workpiece is scratched when the nut is tightened. However, for some important connections, such as places that rely mainly on compression to generate frictional force to transmit power, spring pads cannot be used, and the rigidity of the connection is reduced, which is prone to accidents. Spring washers can be omitted. When the strength of the connected parts is low, use flat washers or Montrealflange bolts to increase the contact area. When there is vibration, pulse, and the temperature of the medium fluctuates greatly, MontrealMontrealspring washers must be used.
At present, in the era of industrialization, rivets used in specific occasions, automobiles, and aviation industries can only rely on professional tools and equipment to complete the riveting method.
In automobiles, wheel nuts are a widely used component. According to the actual use requirements of the wheel nut, there are often spacers on the wheel nut. In this way, the wheel nut and spacer form a wheel nut assembly. However, in the prior art, since the washer is only movably fitted on the wheel nut, when the wheel nut is removed or a large number of wheel nuts are placed, the wheel nut and the washer will be separated. When in use, they need to be assembled one by one, and when they are disassembled or placed again after use, they need to be assembled again, which not only increases the unnecessary workload, but also affects the use effect of the wheel nut in actual use.
Pins are widely used. In the connection of the rotating mechanism of two moving components, such as the crank mechanism, the turning mechanism, the connection between the hydraulic cylinder and the moving parts, the pins are used. kind. In order to ensure the normal use of the running equipment and prevent the cylindrical pin from slipping out and falling off during use, some anti-falling methods are usually used at the head of the pin, such as 1. Drill holes and insert Montrealcotter pins to prevent the pins from slipping out; 2. The external thread is tightened with a nut to prevent the pin from slipping out; 3. The slot is clamped with a circlip to prevent it from slipping out, etc. These measures make the cylindrical pin very practical in the case of infrequent disassembly and assembly, but in the actual use of the field, in order to prevent the collision of some equipment during each troubleshooting or maintenance, the pin needs to be pulled out and turned up, etc. After the failure or maintenance is completed, put down and then insert the pin to restore, this process will bring trouble to the actual operator. For example, special tools must be brought with you every time you disassemble and assemble the pin, and the split pin or the circlip is easily damaged after repeated disassembly and assembly. , In order to save trouble, the operator sometimes uses iron wire to thread or fasten it instead, and even does not remove the pin for the sake of speed and convenience, which is easy to cause damage to the equipment when dealing with faults.
MontrealHexagon nuts are usually used in conjunction with bolts and screws to connect and fasten parts. In daily life, ordinary hexagon nuts are sometimes welded to metal plates for use. In the process of welding hexagon nuts to metal plates In order to ensure that the center line of the inner thread of the hexagonal nut is perpendicular to the metal plate, it is necessary to press the end face of the hexagonal nut on the metal plate before welding. Part of the melt is melted. Since the weld is close to the inner thread of the hexagonal nut, the inner thread is often deformed, which affects the fit of the hexagonal nut and the bolt.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB12617 all stainless steel rivets, serrated MontrealMontreallock washers, disc MontrealMontrealspring washers, standard shelf screws and other products, we can provide you with suitable fasteners. Firmware Solutions.
