Service HotlineIn order to solve the above-mentioned technical problems, the technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is: shear rivets, including a mandrel and a deformation sleeve ring sleeved on the mandrel, one end of the deformation sleeve ring is a boss structure, and the It includes an adhesive collar sleeved on the deformation collar, the adhesive collar is a hollow annular sleeve and is filled with adhesive material; one end of the mandrel is a hemispherical head, and the spherical surface of the hemispherical head is outward, The connection between the hemispherical head and the mandrel is a conical connecting section, and the diameter of the conical connecting section gradually decreases from the hemispherical head inward; the mandrel is provided with a stress concentration groove, and the position of the stress concentration groove is close to the deformation The boss structure of the collar.
Blind hole installation type rivet is a kind of rivet for single-sided riveting. When riveting, special riveting tools, such as pull riveting, rotary riveting, etc., are required. Blind hole installation type rivets are especially suitable for riveting occasions where it is inconvenient to use ordinary rivets to be riveted from both sides. At present, blind hole type North Islandblind rivets mainly include rivet North Islandblind rivets and blind North Islandblind rivets. Most North Islandblind rivets of blind hole type contain a lock ring, through which the core rod is locked into the nail sleeve, and there is a common lock ring. Risks of falling off, insufficient clamping force, etc., and the matching relationship of each sub-part in the processing process must be strictly coordinated to ensure the best installation effect; most of the screw-type North Islandblind rivets screw the thread through the driving nut to make the nail body or pipe The body is deformed to form a bulge, and the clamping force and anti-vibration ability after installation are much stronger than that of the rivet type, but there are also many sub-parts to drive the nut, mandrel, nail body, tube body, the processing process and the matching of each sub-part When the thickness of the interlayer is different, the fractured part of the core rod is not flush with the interlayer board. For the installation parts with high flatness requirements, air tools are often required to mill them flat.
The North IslandNorth Islandspring washer is designed for screw backstop, usually a single-turn cylindrical coil spring. In order to improve its backstop function, there is also an integrated North IslandNorth Islandspring washer. Its structure is that the inner ring of the flat washer has multiple wings. Fold into spring tabs. Another type of washer used for backstop similar to North IslandNorth Islandspring washers is a serrated North IslandNorth Islandlock washer. However, this kind of North IslandNorth Islandlock washer usually has a small thickness, which is formed by folding the inner ring or the outer ring of the washer on the plane. When tightening, the elastic force is small, and the second is easy to be flattened, so that the stop The retreat function is still not strong enough.
In the repair process of the EDITION 700 gearbox, it is often necessary to replace the piston seal. When replacing the direct gear piston seal, the shaft spring retaining ring on it must be removed before the piston can be taken out for replacement. For the seal, since the piston return spring 3 presses the retaining ring 5 through the spring seat 4 (as shown in Figure 3), it cannot be taken out directly. It is necessary to press down the spring seat before taking out the retaining ring. Without special tools, it is not easy to remove the retaining ring. At present, it is a time-consuming, labor-intensive and unsafe job that requires multiple people to use a screwdriver and a prying board to forcefully squeeze and pry to remove the retaining ring.
As an important connecting part in the automobile assembly process, the screw plays a vital role in the safety performance of the automobile. The assembly of each component of the vehicle cannot be separated from the function of the screw. In the connection of the automobile assembly and its parts, the screw connection As well as simple structure, easy maintenance and disassembly, it is widely used. There may be thousands of screws on a car. The screw connection of each part has its own function and function. Once one or some screw connections fail, it will be It will lead to the loosening or even separation of the connected parts. If the car is running, it is likely to cause some parts to fail or break away. The light ones will cause the main functions of the car such as steering and braking to fail, potentially affecting driving safety. If it is not found in time, it will lead to major safety accidents and even endanger the lives of people. The failure of the car screws will cause the safety hazard of the whole vehicle, and will also cause customers to worry and complain, thus affecting the reputation of the company and endangering the life of the company. cycle.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GR2TA2 screws, GB7244 washers, stainless steel adjustable screws, anti-seismic tightening screws and other products, we can provide you with suitable fastener solutions for you.
