Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 11 the result is that the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
It is suitable for plates of various thicknesses, with a minimum thickness of 0.8mm. When using, the tail number Z corresponding to size A must be determined according to the thickness of the plate and the specification of the nut. The user selects samples and orders according to the tail number in the table according to the thickness of the plate; Accurate control, processing according to the tolerance size of 0-+0.075mm, is punching, and the nut should generally be installed from the broken surface of the plate. The installation process is generally achieved through press riveting operations, and must not be impacted and knocked in.
When the tightening effect is achieved by the nut, it is often necessary to use a wrench to fix the nut or turn the nut to achieve the fixing effect. During the use process, the size of the nut is fixed, so it is necessary to use the corresponding type of wrench and the corresponding nut. In the tightening operation, during the installation process, the size of the wrench is large, that is, the nut cannot be manipulated, and it takes time to find a suitable wrench, which is inefficient.
The capped nut can prevent the bolt connection from directly contacting with the outside world, which is corroded and makes it difficult to disassemble later. Nuts with caps in the prior art are mostly of one-piece structure, and the surface is not treated with anti-oxidation, which is easy to be corroded. In addition to the protective effect, the fastening method is the same as that of ordinary nuts, so it is easy to loosen when subjected to severe vibration. .
In the household and industry, when installing furniture, home appliances, electrical appliances, equipment and other objects, the objects are uneven or uneven due to the uneven bottom of the object, or because the placement surface or installation surface is uneven, or because the two surfaces are different and do not fit together. stable, produce vibration, shaking or sliding, affecting the use effect and service life. Sometimes two items need to be placed next to each other, but their surfaces cannot be in direct contact, otherwise the surfaces will be damaged. For these two cases, the common solution is to install gaskets. There are two types of gaskets: wedge and flat. The wedge-shaped gasket adjusts the actual thickness by adjusting the length of the insertion gap, but the contact surface and load-bearing surface of this method are small, and due to its wedge-shaped structure, the gasket may withdraw after being stressed for a long time. OffalyFlat gaskets are generally made from local materials, using waste paper, plastic, rubber, metal and other materials to form the required thickness by folding or stacking. Such gaskets are often not quickly assembled to the exact desired thickness, are not aesthetically pleasing, and are not reusable. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a product that can keep furniture, home appliances, equipment, electrical appliances and other objects horizontal, vertical or stable, prevent them from vibrating, shaking or sliding, and can provide appropriate thickness and beautiful appearance. gasket. The purpose of Yueluo is to realize a gasket that can be combined at will. The sheet 1 is provided with small holes 3 , and the connecting device 2 connects a plurality of sheets 1 together through the small holes 3 . The connecting device 2 is a rivet or a screw. The material of the sheet 1 can be plastic, metal, paper card or rubber. The gaskets provided by Yueluo can be combined at will. Multiple sheets are connected together by rivets or screws. By opening or closing the sheets, or dismantling the screws, the sheets are reassembled to obtain a combination of gaskets with different thicknesses and elasticity. The space between the installation object and the installation surface to keep the object horizontal, vertical or stable and prevent it from vibrating, shaking or sliding.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: fastener nuts, Dongguan Yuelu production, nylon plastic bolts, dome head solid rivets and other products, we can provide you with suitable fastening products piece solution.