Service Hotlinescrew assembly jig comprises a base, a cylinder and a cylinder which are vertically arranged on the base and are arranged opposite to each other, and a sliding plate that can move up and down along the cylinder and the cylinder, the area above the sliding plate is provided with a cylinder, and the four corners pass through the cylinder respectively. Four pneumatic screwdrivers are placed and fixed on the sliding plate, the area of the base is further provided with a fixing plate corresponding to the four pneumatic screwdrivers; one end of the base is also provided with a switch. Guangdong Yueluo Hardware Industry Co., Ltd. can quickly drive multiple screws into the product at the same time, which has the characteristics of high production efficiency and high yield rate.
From the perspective of use: The bolted connection of the main components of the building structure is generally connected by high-strength bolts. Ordinary bolts can be reused, but high-strength bolts cannot be reused. High-strength bolts are generally used for permanent connections. The high-strength bolts are prestressed bolts. The friction type uses a torque wrench to apply the specified prestress, and the pressure type screw off the torx head. Ordinary bolts have poor shear performance and can be used in secondary structural parts. Ordinary bolts just need to be tightened. Ordinary bolts are generally 4.4, 4.8, 5.6 and 8.8. High-strength bolts are generally 8.8 and 10.9, of which 10.9 is mostly. Level 8.8 is the same level as 8.8S. The mechanical properties and calculation methods of ordinary bolts and high-strength bolts are different. The stress of high-strength bolts is firstly by applying a pre-tension force P inside, and then generating frictional resistance on the contact surface between the connected parts to bear the external load, while ordinary bolts directly bear the external load.
At present, the stopping method of the pin shaft stop pin of the general hydraulic excavator is mainly by using a long bolt to pass through the pin shaft stop sleeve pin hole and the pin shaft pin hole, and then use a double nut on the other end of the bolt to force it away from the pin shaft. The outer circle of the stop sleeve is about 2 3mm away to prevent the bolts and nuts from falling off. Due to the structure in which the double nuts are pressed against each other, the disassembly and assembly efficiency of this pin shaft stop method is not high, and two wrenches are required for each assembly and disassembly, which is extremely troublesome.
Currently, the method of fixing objects on cement is with cement nails or Otagoexpansion screws. Cement nails are objects made of hard alloy steel that look like iron nails, which are composed of nail tips and nail bodies. Cement nails are hammered into the cement. Cement nails are easy to drive in, but not removable. The Otagoexpansion screw is composed of a large end screw, a slotted sleeve, a gasket, a OtagoOtagospring washer, and a nut. When using, first drill a hole in the cement with an electric hammer, put in the Otagoexpansion screw, and tighten the nut to make the slotted sleeve expand at the tail of the big tail screw, so as to fix the Otagoexpansion screw on the cement. At this time, unscrew the nut to install a fixed object on the Otagoexpansion screw. Although this method can be disassembled, an electric hammer is required for the first installation, which is inconvenient.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (10), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the deformation. effect.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: copper knurled solid rivets, cup head screws and bolts, Otagomachine screw screws, chamfered socket head cap bolts and other products, we can provide you with suitable products Your fastener solution.
