Service HotlineAt present, Otagoshaft retaining rings are mainly divided into three categories: elastic retaining rings for shafts, flattened wire retaining rings for shafts, and wire retaining rings for shafts. Among them, the spring retaining ring for the shaft is generally installed with circlip pliers, and the flattening wire retaining ring for the shaft and the wire retaining ring for the shaft are generally installed with a sharp screwdriver or needle-nose pliers. The defects and deficiencies of these two methods will be discussed in detail below: First, the above two installation methods require the operator to use a large force to open the retaining ring, which is more laborious; For the installation of the flattened steel wire retaining ring for the shaft and the steel wire retaining ring for the shaft, because the wire retaining ring has low elasticity and has no force point, it is very easy to cause the retaining ring to break or the installation tool to slip during the installation process. Higher skills and experience can be competent for the installation of wire retaining rings.
Screw (pinyin: luógǎn, English: screw): a cylinder with a spiral groove cut on the outer surface or a cone cut with a tapered spiral groove. The screw has a different head, the head is called an external hexagon screw. There are others, such as large flat screws, socket head screws and so on.
The semicircular key is a kind of key, the upper surface is a plane, the lower surface is a semicircular arc surface, the two sides are parallel, commonly known as the crescent key. It is basically the same as the flat key connection method, but it is more convenient to manufacture and disassemble than the flat key, and is especially suitable for the connection between the tapered shaft and the hub. The half-round key transmits torque on the side, but the keyway is deep, which weakens the shaft greatly. Due to the deep keyway, the bottom of the keyway is easily deformed after the shaft is heat treated. Therefore, when the semicircular key and the keyway are assembled in a transitional fit relationship, the interference between the lower part of the semicircular key and the bottom of the keyway often occurs, resulting in difficult or impossible assembly. Assembly situation. In order to solve the above technical problems, the current method is to make the thickness of the semicircular key appropriately thin, so that the semicircular key and the keyway are clearance fit, which brings about a large gap between the upper part of the semicircular key and the keyway, and the semicircular key is in operation. Difficult to locate in the keyway, affecting smooth transmission.
The purpose of Yueluo is to provide a screw with a plurality of threads continuously coiled in a helical shape formed on its shank; wherein the shank is provided with a protruding cutting portion at the front section with threads toward the tip, for the purpose of providing the screw. The front section is screwed into the object to successfully complete the stage of cutting and rapid chip removal, and the rod part is provided with a concave cutting part at the rear section with threads toward the head, for the rear section of the rod to be introduced into the object. , so that the work of the stage of cutting and collecting chips can be successfully completed; so that the screw can achieve multiple functions such as labor-saving cutting, smooth and rapid chip removal and chip collection during the locking process.
Contents of the utility model Guangdong Yueluo Hardware Industry Co., Ltd. is to solve the problem of needing one hand to hold the screw when screwing the screw at present, and to provide a screw fixture that can screw the screw without holding the screw by hand. Guangdong Yueluo Hardware Industry Co., Ltd. adopts the following technical solutions. Guangdong Yueluo Hardware Industry Co., Ltd. includes a clamp sleeve, and the middle of the clamp sleeve is a through hole. The outer end of the pivot pin is in contact with the spring. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is because Guangdong Yueluo Hardware Industry Co., Ltd. is provided with a rotating pin on the shaft of the fixture sleeve that can contact the screw, and the outer end of the rotating pin is in contact with the spring, so that the screw It is easy to fix in the through hole of the fixture cover, and the screwdriver is also in the through hole of the fixture cover, which ensures the alignment of the screw and the screwdriver, so it is avoided to hold the screw by hand, and the screw is quickly screwed to the object. in vivo.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: carbon steel galvanized pins, percussion flat cap rivets, boxed screws and nuts, Daquan 304 stainless steel nuts and other products, we We can provide you with the right fastener solution for you.
