Service HotlineIn the riveting operation, the rivet used is composed of a mandrel and a deformed collar. When in use, a through hole is drilled on the two components to be connected, and then the head of the rivet is passed through the through hole and clamped by a rivet. The tail of the rivet will break the rivet, the head of the rivet and the deformed collar remain in the through hole, and the whole riveting process is completed. The existing pull rivets have the following shortcomings: first, the parts where the pull rivet and the two components are connected cannot be completely and tightly fitted, which meets the requirements of non-sealing for parts that have waterproof and leak-proof requirements; second, the existing pull rivets The separation groove of the rivet mandrel is close to its head. When the mandrel is broken by the rivet during the riveting process, basically only the head of the mandrel remains in the deformation collar, and the connection of the two components depends on the deformation of the collar. Under the action of compressive stress, the inside of the deformed collar becomes hollow due to the breaking of the mandrel, and cannot bear large shear stress.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bayonet which is a T-shaped cylindrical pin with a misaligned through hole at the head, and a bayonet spring which is a ring-shaped spring steel wire whose ends are staggered. The retaining ring is clamped by the bayonet pin to fix the stop sleeve and the pin shaft together. A hydraulic excavator pin stopper with high disassembly and assembly efficiency and no need for a wrench. The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is such that it includes a latch, a stop sleeve, a pin, a bayonet, and a circlip. The staggered end is clamped into the misaligned through hole of the plug, and screwed on the bottom of the stopper sleeve to fix the stopper sleeve and the pin shaft together. The latch is composed of a bayonet pin and a circlip, the circlip is screwed around the through hole of the bayonet pin to the root of the bayonet pin, and the stopper sleeve is tightly wrapped around the pin shaft, and the circlip is tightly against the bayonet pin. The head of the bayonet pin has two T-shaped cylindrical pins with staggered through holes, and the circlip is an annular spring steel wire whose ends are staggered. By adopting the pin shaft stopping method of the above technical scheme, it is extremely convenient and quick to disassemble and assemble the pin shaft. The bolt of Guangdong Yueluo Hardware Industry Co., Ltd. is only composed of a T-shaped cylindrical pin with two staggered through holes in the head and a ring-shaped spring steel wire with staggered ends. The structure is simple, convenient to manufacture, low cost and obvious. It is an excavator pin stop method with high disassembly and assembly efficiency, no need for a wrench and low manufacturing cost.
The flat washer is mainly used to reduce the pressure. When some parts are tightened with a large axial force, it is easy to press the washer into a dish shape. At this time, it can be solved by changing the material and increasing the hardness.
The screw and nut disassembly and assembly tool of Yueluo also includes a rotating rod, a sleeve and a fixed rod fixedly connected to the sleeve rod at one end, and the other end of the fixed rod is connected with one end of the rotating rod to make the rotation The rod can be rotated around the connection point, and the sleeve for accommodating nuts or screws is fixedly connected with the other end of the rotating rod; rotating the rotating rod makes the sleeve head and the opening of the sleeve opposite , by keeping the nut or screw in the sleeve fixed while the corresponding screw or nut in the sleeve head rotates, so as to achieve simultaneous force and disassembly of the screw and the nut.
Gears, mechanical components with teeth on the rim that can continuously mesh to transmit motion and power, are mechanical parts with teeth that can mesh with each other. The gears used in industry are generally made of steel. The commonly used steels are quenched and tempered steel, hardened steel, carburized and quenched steel and nitrided steel. The strength of cast steel is slightly lower than that of forged steel, and it is often used in Larger-sized gears; gray cast iron has poor mechanical properties and can be used in light-load open gear transmissions; ductile iron can partially replace steel gears; plastic gears are mostly used in places where light loads and low noise are required, and are matched with them The gears are generally made of steel gears with good thermal conductivity.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: zinc outer diameter 7.2SOO, GB617086, carbon steel color zinc screws, aluminum sign rivets and other products, we can provide you with suitable fasteners for you solution.
