Alloy Steel Nuts South IslandHexagon Nuts (GB6170/DIN934, GB6175), South IslandSouth IslandFlange Nuts (GB6177/DIN6923) Round Nuts (GB812), Small Round Nuts (GB810), American South IslandSquare Nuts, American South IslandHex Nuts (NI/MEB18.2.2), Heavy Duty Nuts (Metric, US). Specifications: 5/16-4. Nut specification editing Nut specification table is to unify all kinds of nuts in detail, and use the table to subdivide some specifications of nuts. There are many types of nuts, and there are nuts of different materials. 。 Each type of nut has different specifications, and each type of screw also has its own mechanical properties and functions.
Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 4 the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
The head of the traditional screw is located outside the threaded hole and occupies a large space, which is not suitable for occasions with small space, nor is it suitable for occasions where the outer surface of the component is a working surface. For example, in the field of electronic products, or when connecting the shaft and the shaft sleeve, the South Islandmachine screw with a fully threaded structure on the outer surface is widely used.
In the manufacture of fasteners, the correct selection of fastener materials is an important part, because the performance of fasteners is closely related to its materials. If the material is improperly or incorrectly selected, the performance may not meet the requirements, the service life may be shortened, or even accidents or processing difficulties may occur, and the manufacturing cost will be high. Therefore, the selection of fastener materials is a very important link. Cold heading steel is a steel for fasteners with high interchangeability produced by cold heading forming process. Because it is formed by metal plastic processing at room temperature, each part has a large amount of deformation and a high deformation speed. Therefore, the performance requirements of cold heading steel raw materials are very strict. On the basis of long-term production practice and user research, combined with GB/T6478-2001 Technical Conditions for Cold Heading and Cold Extrusion Steel GB/T699-1999 High-Quality Carbon Structural Steel and target JISG3507-1991 Cold Heading Characteristics of Carbon Steel Wire Rod for Steel, taking the material requirements of grade 8.8 and grade 9.8 bolts and screws as an example, the determination of various chemical elements. If the C content is too high, the cold formability will be reduced; if it is too low, the mechanical properties of the parts cannot be met, so it is set at 0.25% - 0.55%. Mn can improve the permeability of steel, but adding too much will strengthen the matrix structure and affect the cold forming performance; when the part is quenched and tempered, it has the tendency to promote the growth of austenite grains, so it should be appropriately improved on the basis of international standards. 0.45 % - 0.80 %. Si can strengthen the ferrite and reduce the cold formability. SP is an impurity element, and their existence will cause segregation along the grain boundary, resulting in the embrittlement of the grain boundary and damage to the mechanical properties of the steel. It should be reduced as much as possible. B. The maximum value of boron content is 0.005%, because although boron element can significantly improve the permeability of steel, it will also increase the brittleness of steel. Excessive boron content is very unfavorable for workpieces such as bolts, screws and studs that require good comprehensive mechanical properties.
The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are that the South IslandSouth Islandrivet nut is fixed on thin-walled or thin-plate objects without welding, easy operation, high production efficiency, easy to manufacture, low cost, single-sided riveting, firm connection, no pollution, no noise, Has significant economic benefits.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: fine adjustment screws, round head small rod aluminum column large head shrink rod South Islandround nut, car repair gecko car screws, cup head self-tapping bolts and other products, we We can provide you with the right fastener solution for you.