Service HotlineSouth Islandcaptive screw is a commonly used pressure riveting part. Usually the South Islandcaptive screws are directly riveted on the motherboard, so as to play the role of fixing the components, and there is a high requirement for the distance between the opening holes on the component. Once the distance between the through holes on the component and the If the distances between the riveting holes on the motherboard do not match, the components cannot be riveted on the motherboard, which will result in defective or scrapped products, thereby increasing production costs and reducing production efficiency.
At present, machinery and equipment have gradually become the main force of work production. Many equipment require frequent maintenance and even replacement of parts during use. During the process of maintenance and replacement, it is inevitable to encounter the problem of screw disassembly and assembly. In the process of disassembly and assembly, it is almost necessary to cooperate with both hands, or because the thread is too long, installation and disassembly are very cumbersome. Especially in the butt installation of flanges, bolts and nuts are used for clamping and fixing at this stage. During use, two hands are required to hold a board, a fixed screw, and a screw nut. This is to prevent the nut from During the turning process, the screw also rotates. When screwing, the wrench should be taken down without interruption, re-selected a good position, and then screw the screw forcefully again, and repeated several times before the screw can be unscrewed. Time and labor costs for maintenance are wasted. At present, there is no screw that is easy to install and remove.
1. The twisted screw should be considered according to the actual inner diameter of the barrel, and the outer diameter deviation of the new screw should be given according to the normal clearance with the barrel. 2. After the thread surface with the reduced diameter of the worn screw is treated, the wear-resistant tungsten carbide alloy is thermally sprayed, and then ground to size. 3. Surfacing wear-resistant tungsten carbide alloy on the thread part of the worn screw. According to the degree of screw wear, surfacing welding is 1~2mm thick, and then the screw is ground and processed to size. This wear-resistant tungsten carbide alloy is composed of materials such as C, Cr, Vi, Co, W and B, which increases the wear resistance and corrosion resistance of the screw. 4. The bottom diameter of the screw is repaired by electroplating hard chromium. Chromium is also a wear-resistant and corrosion-resistant metal, but the hard chromium layer is easier to fall off.
Please refer to FIG. 1 , which is a cross-sectional view of a conventional screw and screw washer for locking two metal parts. The screw 100 is combined with the screw washer 110 to lock the metal parts 120 and 130 . The screw washer 110 includes a washer portion 112 and a body washer portion 114 . The washer portion 112 is used for electrically isolating the screw head 102 from the metal piece 120 , and the screw body washer portion 114 is used for electrically isolating the screw body 104 and the metal piece 120 . Therefore, through the design of the screw washer 110 , the screw 100 can be isolated from conducting the metal parts 120 and 130 .
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a flat gasket that improves the lubrication performance of the contact surface and reduces the friction of the contact surface. Yueluo is implemented through the following technical solutions: a flat gasket with straight upper and lower end faces, characterized in that: the upper and lower end faces are dotted with pits, the pits are spherical pits, and the pit diameter is 2-3mm , the pit depth is between 0.5-lmm. The bottoms of some of the pits are provided with through holes penetrating the upper and lower end faces, and the diameter of the through holes is not greater than 0.5mm. The flat gaskets provided by Yueluo have pits with reasonable design parameters on the upper and lower end faces of the flat gaskets. The pits can store oil, so the lubrication of the contact surfaces of the gaskets can be well improved. It can effectively reduce the friction of the contact surface of the gasket and reduce the failure rate; in addition, the design of the through hole enables a smooth oil passage between the upper and lower end faces of the gasket, ensuring that the upper and lower end faces can be well lubricated.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: cabinet nuts and screws, trapezoidal nuts, ring screws, cross rivets and other products, we can provide you with suitable fastener solutions for you.
