Service HotlineThe technical scheme adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is: a pin pressure riveting structure, including a pin, a cavity and a pressure riveting fixture, the pin is a columnar structure, an annular groove is arranged on the surface of the pin, and the cavity is The body is provided with a light hole, the depth of the light hole is greater than the height of the annular groove relative to the bottom of the pin, the lower end of the pin is inserted into the light hole, the pressure riveting fixture includes a pressure riveting part and a pressure-bearing part located on the top of the pressure riveting part, so The riveting part and the pressure-bearing part are provided with coaxial and penetrating connecting holes, and the upper ends of the pins are sleeved in the connecting holes.
High-strength fasteners must be quenched and tempered according to technical requirements. The purpose of heat treatment and tempering is to improve the comprehensive mechanical properties of fasteners to meet the specified tensile strength value and yield ratio of the product. The heat treatment process has a crucial impact on high-strength fasteners, especially its intrinsic quality. Therefore, in order to produce high-quality high-strength fasteners, advanced heat treatment technology and equipment must be available. Due to the large production volume and low price of high-strength bolts, and the threaded part is a relatively fine and relatively precise structure, the heat treatment equipment is required to have large production capacity, high degree of automation, and good heat treatment quality. Since the 1990s, the continuous heat treatment production line with protective atmosphere has dominated, and the shock bottom type and mesh belt furnace are especially suitable for heat treatment and tempering of small and medium-sized fasteners. In addition to the good sealing performance of the furnace, the quenching and tempering line also has advanced computer control of atmosphere, temperature and process parameters, equipment failure alarm and display functions. High-strength fasteners are automatically controlled and operated from feeding-cleaning-heating-quenching-cleaning-tempering-coloring to offline, which effectively ensures the quality of heat treatment. The decarburization of the thread will cause the fastener to trip before the resistance required by the mechanical properties is reached, which will cause the failure of the threaded fastener and shorten the service life. Due to the decarburization of the raw material, if the annealing is improper, the decarburized layer of the raw material will be deepened. In the process of quenching and tempering heat treatment, some oxidizing gas is generally brought in from outside the furnace. The rust of the bar wire or the residue on the surface of the wire rod after cold drawing will also decompose after being heated in the furnace, and some oxidizing gases will be generated by the reaction. For example, the surface rust of steel wire, which is composed of iron carbonate and hydroxide, will be decomposed into CO₂ and H₂O after heating, thus aggravating decarburization. South IslandStudies have shown that the degree of decarburization of medium carbon alloy steel is more serious than that of carbon steel, and the fastest decarburization temperature is between 700 and 800 degrees Celsius. Because the attachments on the surface of the steel wire decompose and synthesize carbon dioxide and water very quickly under certain conditions, if the furnace gas of the continuous mesh belt furnace is not properly controlled, it will also cause excessive decarburization of the screw. When the high-strength bolt is formed by cold heading, the raw material and the annealed decarburized layer not only still exist, but also are extruded to the top of the thread. For the surface of the fastener that needs to be quenched, the required hardness cannot be obtained. Its mechanical properties (especially strength and wear resistance) decreased. In addition, the surface of the steel wire is decarburized, and the surface layer and the internal structure have different expansion coefficients, and surface cracks may occur during quenching. For this reason, during quenching and heating, the top of the thread should be protected from decarburization, and the fasteners whose raw materials have been decarburized should be properly carbonized, and the advantages of the protective atmosphere in the mesh belt furnace should be adjusted to the original carbon-coated parts. The carbon content is basically the same, so that the decarburized fasteners are slowly restored to the original carbon content. The carbon potential is preferably set at 0.42% - 0.48%. The carbon coating temperature is the same as the quenching heating, and cannot be carried out at high temperatures , so as to avoid coarse grains and affect mechanical properties. The quality problems that may occur in the process of quenching and tempering of fasteners mainly include: insufficient hardness in the quenched state; uneven hardness in the quenched state; excessive quenching deformation; quenching cracking. Such problems in the field are often related to raw materials, quenching heating and quenching cooling. Correctly formulating the heat treatment process and standardizing the production operation process can often avoid such quality accidents.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide an improved lock nut to solve the problem that the production technology of the prior art products is too complicated. For realizing the above-mentioned purpose, Guangdong Yueluo Hardware Industry Co., Ltd. adopts following technical scheme—a kind of locking nut, which comprises that the bottom of the nut is a circle, the middle part is a hexagon, and the top is a circle, and there are bolts in the center.
The retaining ring is a ring-shaped component fastened on the shaft and the inner hole. Its main function is to prevent other components installed on the shaft and the inner hole from sliding axially on the shaft. It is a fixed standard part.
Most electrical appliance manufacturers only require the size and riveting gap to be tested for riveted contact components. There is no clear requirement for riveting strength. Only a few manufacturers perform torsion testing on riveting strength. The torque detection method is as follows: use a saw blade to open a one-shaped groove on the rivet head of the riveted contact element, and then insert a torque wrench into the one-shaped open groove to rotate, and measure the torque value. Because most of the electrical contacts are made of copper-silver alloy, the strength is low, and it is easy to slip during the test, and when a saw blade is used to open the one-shaped groove, the width and depth cannot be accurately positioned, so the measured value fluctuates greatly. , has always been an unsolvable technical problem in the industry.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: accessories hexagonal screws, elastic cylindrical positioning pins, wide South IslandSouth Islandspring washers, hollow rubber columns and other products, we can provide you with suitable tightening. Firmware Solutions.
