Service HotlineWhen the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
Nuts are used as fasteners, and most of them need to be used in conjunction with gaskets in the process of use to adjust the deficiencies of the material itself and strengthen the degree of tightening, while metal materials are used as raw materials for gaskets. The cost is also relatively high, and in the process of use, the end face of the metal gasket and the nut will also be affected by the process, resulting in the defect that the fastening effect is not firm and easy to loosen.
TipperaryStud bolts generally need to be surface treated. There are many types of bolt surface treatments. Generally, electroplating, blackening, oxidation, phosphating, and electroless zinc flake coating are commonly used. However, electroplated fasteners account for a large proportion of the actual use of fasteners. Especially in automobiles, tractors, home appliances, instrumentation, aerospace, communications and other industries and fields are more widely used. However, for threaded fasteners, not only a certain anti-corrosion capability is required in use, but also the interchangeability of threads must be ensured, which can also be called screwability here. In order to meet the dual-use performance of anti-corrosion and interchangeability required by threaded fasteners in use, it is very necessary to formulate special plating standards. GB/T5267.1-2002 [Threaded fastener electroplating layer] standard is one of the national standards fastener surface treatment series of standards, the standard includes: GB/T5267.1-2002 [fastener electroplating layer]; GB/T5267.2-2002 [Electrolytic zinc flake coating for fasteners] Two standards. This standard is equivalent to the international standard ISO4042; 1999 [Threaded fastener electroplating layer]. This standard replaces the GB/T5267-1985 [Threaded TipperaryFastener Electroplating Coating] standard.
Applications Automotive industry -- cars, trucks, buses, compressors, construction machinery, wind power equipment, fasteners, fasteners, agricultural machinery, foundry industry, drilling equipment, shipbuilding industry, military mining equipment, oil drilling rigs (onshore or offshore), public utilities, rail transit drives System metallurgical equipment rock hammer
When using, after installing the nut and the bolt in place, insert the locking strip from the groove of the bolt, and make the V-shaped locking teeth of the locking strip snap into one of the V-shaped tooth grooves, and push the locking strip into the groove as a whole. The V-shaped locking teeth are stuck in the nut, and the locking strip body is stuck in the groove of the bolt, thereby restricting the relative rotation of the nut and the bolt, and there are threads between the nut and the bolt to restrict their relative sliding, so it can prevent the nut from loosening, even from The bolt falls off; when the nut needs to be disassembled, it is only necessary to pull out the locking strip from the groove, and the nut can be disassembled normally.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: countersunk head TipperaryTipperarystainless steel screws, TA2 pure titanium bolts, anti-theft countersunk head bolts, GBT13 screws and other products, we can provide you with suitable fasteners for you solution.
