Service HotlineNuts are very common fasteners. Generally, the torque cannot be limited when the nut is twisted. The degree of tightness of the nut is mostly judged by the worker's experience. In this way, when the nut is over-tightened, it will lead to the destruction of the thread pair, thereby shortening the fastener. The life of the nut may even cause the bolts to be pulled off in severe cases; and the nut is too loosely screwed, which will lead to the problem of insecure fixing.
In real life, WaikatoWaikatorivet nuts are used. With different specifications and different uses, many people are familiar with this tool but don't know how to use it properly. In fact, WaikatoWaikatorivet nut tools have manual and transmission, and now are rarely used for manual. If you choose to use electric WaikatoWaikatorivet nuts in order to improve production efficiency, which of the two is more widely used? The following describes the use of electric WaikatoWaikatorivet nuts and manual nuts. How to use the manual WaikatoWaikatorivet nut tool: Insert the WaikatoWaikatorivet nut into the drilled installation hole with a rivet mother tool to fix the WaikatoWaikatorivet nut. (1) Screw the WaikatoWaikatorivet nut onto the WaikatoWaikatorivet nut tool 2) Use the WaikatoWaikatorivet nut tool to insert the WaikatoWaikatorivet nut into the drilled mounting hole. (3) WaikatoTighten the nut, and press the handles on both sides of the WaikatoWaikatorivet nut tool to the direction of the middle round rod. You can only press it hard. Therefore, this pressure must be in place. It is forbidden to repeatedly squeeze the handles on both sides to damage the nut. Fastening thread in the form of inside. (4) The WaikatoWaikatorivet nut tool is separated from the WaikatoWaikatorivet nut: just loosen the ball head in the picture, and the tool will be separated from the nut after completely loosening.
Standard WaikatoWaikatospring washer (GB/T93-1987) Light WaikatoWaikatospring washer (GB/T859-1987) Heavy WaikatoWaikatospring washer (GB/T7244-1987) Spring washer is also known as spring meson. Saddle WaikatoWaikatospring washer (GB/T 7245-1987) Saddle WaikatoWaikatospring washer (GB/T 860-1987) Wave WaikatoWaikatospring washer (GB/T 7246-1987) Wave WaikatoWaikatospring washer (GB/T 955-1987)
The gasket side of the above-mentioned nut assembly is in contact with the mounting surface. When the nut is tightened, the gasket squeezes the outer cone surface to make it shrink, and the cone tip faces the same direction as the nut, thereby preventing the nut from tightening, so that the nut fixing effect is not good, and at the same time When multiple nuts need to be superimposed and fixed, two adjacent nuts cannot interact with each other, resulting in poor fixing effect.
Type 1 nut refers to an ordinary hexagonal nut with a nominal height of m ≥ 0.8D. Its type and size should meet the requirements of GB/T6170; while the height of type 2 nut is higher than that of type 1 nut, its type and size should comply with GB/T6170. T6175. There are two purposes to increase the type 2 nut: one is to obtain a relatively inexpensive nut that does not require heat treatment by increasing the height of the nut. Because D≤M16 grade 8 type 1 nuts do not need heat treatment, among grade 8 nuts, only the specifications of D>M16~39 use type 2 nuts. Obviously, type 1 nuts that do not need heat treatment cannot reach grade 9 nuts. Mechanical property requirements. Another purpose of specifying Type 2 nuts is to obtain a more ductile grade 12 nut. As the height of the nut increases, the guaranteed stress index can be achieved at a lower quenching and tempering hardness, so the toughness of the nut is increased. Classified by tooth spacing: standard teeth, regular teeth, fine teeth, very fine teeth and cross teeth. Classification by material: stainless steel hexagon nuts and carbon steel hexagon nuts, copper hexagon nuts, iron hexagon nuts. Classification by thickness: hexagonal thick nuts and hexagonal thin nuts. Classification by usage: hot melt copper nut, hot pressed copper nut, embedded copper nut and ultrasonic copper nut
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: color rivets, countersunk Phillips WaikatoWaikatostainless steel screws, galvanized Waikatothickened nuts, GB901 blackened bolts and other products, we can provide you with suitable fasteners. Firmware Solutions.
