Service HotlineThe specifications of copper inserts are: internal thread specification 1/4-20, outer diameter 10mm, length 15mm mesh pattern copper nut, drawn from flower pull raw materials. The automatic lathe completes at one time: stocking → chamfering → drilling → hooking chamfering → tapping. Stable size, no eccentric internal thread. Material selection: copper C3604, Rohs PASS. The copper nut is used in injection molded parts.
Existing bolt pairs usually include bolts, nuts and washers, and their specific structures and usage methods are traditionally known and common in life. They will not be described in detail here. You can find relevant bolt pairs by searching for bolt pairs on the Internet. Information picture, the structure of the ordinary bolt pair has basically no structural improvement since it was used as a fastener. The production requirements of ordinary bolt pairs are the basic material, structural strength, and accuracy requirements, while the tightening and anti-loosening requirements The requirements of the effect are basically to achieve the problem of tightening and anti-loosening by using elastic washers, anti-loosening washers or using double nuts.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (3), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the amount of deformation effect.
The marking format of the thread mark is: Thread code - thread tolerance zone code (pitch diameter, top diameter) - screw length l) Tolerance zone code is represented by numbers plus letters (inner thread with uppercase letters, external thread with lowercase letters) , such as 7H, 6g, etc., it should be specially pointed out that 7H, 6g, etc. represent thread tolerance, while H7, g6 represent cylinder tolerance code. 2) The length of rotation is specified as short (represented by S), medium (represented by N), and long (represented by L). In general, the thread engagement length is not marked, and the thread tolerance zone is determined by the medium engagement length (N). If necessary, add the screw length code S or L, such as M20-5g6g-L. When special needs are required, the value of the screwing length can be indicated, such as M20-5g6g-30.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: WaikatoWaikatohandle screws, hexagon nuts and nuts, metric thread screws, Waikatoenlarged nuts and other products, we can provide you with suitable fastener solutions for you.
