Service Hotlinesafety screw includes a screw rod, and is characterized in that: the two ends of the screw rod are respectively provided with notches for rotating a tool knife. Compared with the prior art, the advantage of Guangdong Yueluo Hardware Industry Co., Ltd. is that notches are provided at both ends of the screw, so that when the screw is in use, it can be tightened or loosened from both ends without installation. Due to the limitation of position and structure, when the installation space is small or the tool knife cannot be inserted, it is convenient for the operator to directly tighten or loosen the screw from the other end, which improves the efficiency of installation and disassembly, saves assembly time and reduces assembly difficulty.
Bearings are an important component in contemporary machinery and equipment. Its main function is to support the mechanical rotating body, reduce the friction coefficient during its movement, and ensure its rotation accuracy. Every time the locomotive is repaired, the end cover of the axle box needs to be disassembled, the axle head is tested for flaws and the bearing is supplemented with grease, which involves the disassembly and assembly of the axle box bearing retaining ring. The existing disassembly method is to use the traditional method of inserting two tongue pins into the gap between the bearing retaining ring and the axle box to pry left and right, and slowly separate it from the axle head. Because the clearance between the bearing retaining ring and the shaft head is small, and the adhesive force generated by the grease in the axle box is large, if the disassembly method is not appropriate or the force is not uniform, it will cause certain damage to the axle box body and the bearing retaining ring or jam. It is easy to cause damage to the bearing, and there is also the possibility of damage to the disassembly and assembly tools, so the safety risk is high, and each disassembly and assembly of the bearing retaining ring is time-consuming and laborious, labor-intensive, low-efficiency, and increased maintenance costs.
WellingtonWellingtonWellingtonWellingtonCountersunk head screws are mostly used after installation, and the surface of the parts cannot be raised, and the parts to be fastened have two thicknesses. Thickness, after the screw is tightened, there is still a part of the screw thread that does not enter the threaded hole. In this case, the countersunk head screw can definitely be tightened. There is usually a situation where the thickness of the fastened part is less than the height of the head of the countersunk head screw, which is commonly seen in sheet metal parts in mechanical equipment, such as the connection between the hinge of the chassis and the door and the box; the sheet metal of the equipment The connection of the cover to the equipment, etc. Due to the small thickness of the part, the tightened sheet metal part, the screw through hole completely becomes a conical hole, in this case, when the countersunk head screw is tightened, the screw head is not a tapered surface to press the sheet metal part , but the bottom of the screw head and the top of the threaded hole are squeezed. Although it feels that the screw is tightened, the sheet metal part is stuck instead of being pressed. In this case, although it feels that the screw is tightened, the sheet metal The gold pieces were indeed not tightened. This is a very common situation. Let’s talk about the reasons for the processing: the head cone of the countersunk screw has a 90° conical angle, and the apex angle of the newly bought drill is usually 118°-120°. Some workers who lack training do not know this angle is poor. It is often used to ream the hole with a 120° drill bit, which results in that when the countersunk head screw is tightened, it is not the conical surface of the head, but a line at the bottom of the screw head, which is one of the reasons why the so-called countersunk head screw cannot be tightened. , it's not the screw's fault.
Most of the existing screws use an integral metal structure, and there are still some problems, such as large weight, high cost of materials, wear resistance, hardness, rust resistance, corrosion resistance, high and low temperature resistance, brittleness, toughness, etc. Many occasions cannot meet the needs of production, and further improvements are needed to improve production efficiency, reduce costs, improve safety, and prolong the service life of screws.
The embossing wheel is used to press the mesh pattern (rolling mesh pattern), and the middle is slotted. After milling, the thread still guarantees 6H accuracy. This knurled copper nut is used in power tools, which is different from other knurled copper nuts. The diamond pattern of this knurled copper nut is located in the middle section of the product, and the diamond-shaped mesh knurling wheel rolls the diamond-shaped flower along the large outer circular step surface.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: knock-on nuts, flat-head screws, hand-tightened knob nuts, iron clip nuts, WellingtonWellingtoncrown screws and other products, we can provide you with suitable products for you. WellingtonFastener Solutions.
