Service HotlineThe beneficial effects of Guangdong Yueluo Hardware Industry Co., Ltd. are: in Guangdong Yueluo Hardware Industry Co., Ltd., the rivet fixing mechanism is used to temporarily fix and position the rivet, and the pressure cylinder is used to drive the movement of the final shaft, so that the insertion nozzle can be Insert the rivet located in the rivet fixing mechanism into the product. Guangdong Yueluo Hardware Industry Co., Ltd. adopts mechanical drive and transmission, which has a high degree of automation and high work efficiency.
Installation method broadcast 1. One-time burying method: When pouring concrete, bury the anchor bolts. When the high tower is controlled by overturning, the anchor bolt should be buried once. 2. Reserved hole method: The equipment is in place, the holes are cleaned, the anchor bolts are placed in the holes, the equipment is positioned and aligned, and then poured with non-shrinkage fine stone concrete that is one level higher than the original foundation, and compacted and compacted. . The distance from the center of the anchor bolt once buried to the edge of the foundation should not be less than 2d (d is the diameter of the anchor bolt), and should not be less than 15mm (d≤20, it should not be less than 10mm), not less than half the width of the anchor plate Add 50mm, when the above requirements cannot be met, appropriate measures should be taken to strengthen it. The diameter of the anchor bolts used for the structure should not be less than 20mm. When subjected to earthquake action, double nuts should be used for fixing, or other measures to effectively prevent loosening should be adopted, but the anchorage length of anchor bolts should be increased by 5d compared with the anchorage length of non-seismic action. Installation planning of anchor bolts Treatment of anchor bolts loose in the foundation When the anchor bolts are tightened, the bolts may be pulled out. At this time, the bolts should be adjusted to their original positions, and the foundation around the bolts should be shoveled out enough. , and then weld two U-shaped steel bars vertically and horizontally on the bolts, and finally clean the pit with water and grouting, and then tighten the live anchor bolts after the concrete has solidified to the design strength. The treatment method of the live anchor bolt deviation is roughly the same as the dead ground. The method for the anchor bolts is the same, except that the anchor bolts can be pulled out for processing. If the bolt is too long, a section of the thread can be cut off on the machine tool; if the bolt is too short, it can be extended by hot forging; if the position is inconsistent, it can be corrected by bending. Application industry: suitable for various equipment fixing, steel structure foundation embedded parts, street lights, traffic signs, pump, boiler installation, heavy equipment embedded fixing, etc.
Most electrical appliance manufacturers only require the size and riveting gap to be tested for riveted contact components. There is no clear requirement for riveting strength. Only a few manufacturers perform torsion testing on riveting strength. The torque detection method is as follows: use a saw blade to open a one-shaped groove on the rivet head of the riveted contact element, and then insert a torque wrench into the one-shaped open groove to rotate, and measure the torque value. Because most of the electrical contacts are made of copper-silver alloy, the strength is low, and it is easy to slip during the test, and when a saw blade is used to open the one-shaped groove, the width and depth cannot be accurately positioned, so the measured value fluctuates greatly. , has always been an unsolvable technical problem in the industry.
The rod end of the ceramic production equipment is installed with the rod shaft, and then fixed by the cylindrical pin. At present, it is purely manual installation. It is impossible to ensure that the cylindrical pin is kept horizontal during the installation process, and the installation pressure of the cylindrical pin cannot be sensed. The pressure is too large. Cracks in the rollers, too low pressure, and easy loosening of the metal cap; it is impossible to install three or more cylindrical pins at the same time, and it is difficult to align the cylindrical pins with the pin holes of the cylindrical pins, resulting in low efficiency.
WinnipegWinnipegFlat washers are usually thin pieces of various shapes used to reduce friction, prevent leakage, isolate, prevent loosening, or distribute pressure. Such components are found in many materials and structures to perform a variety of similar functions. Restricted by the material and process of threaded fasteners, the bearing surface of fasteners such as bolts is not large, so in order to reduce the compressive stress of the bearing surface and protect the surface of the connected parts, washers are used. In order to prevent the loosening of the connection pair, anti-loose WinnipegWinnipegspring washers, multi-tooth WinnipegWinnipeglock washers, Winnipeground nut Winnipegstop washers and saddle, wave and conical elastic washers are used.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: DIN979 hexagon slotted nuts, hexagonal screws, manganese steel wave washers, cross pan head screws and other products, we can provide you with suitable tightening screws. Firmware Solutions.
