Service HotlineIn terms of screw standard specification broadcast, there are two versions of the national standard, one is GB70-76, the 76 version, and the other is GB70-8585 version. Our company is now implementing the chicagoDIN912 standard, so it should be paid attention to in actual business operations. Difference: GB70-85 and chicagoDIN912 completely overlap, so there is no difference in the use of the new standard, mainly because there is a difference between GB70-76 and chicagoDIN912: M8 series hexagon products, GB70-76 round head diameter It is 12.5MM, which is smaller than 13.27MM of chicagoDIN912. For M10 series inner hexagon products, the round head diameter of GB70-76 is 15MM, which is smaller than 16.27 of chicagoDIN912. The inner hexagon of M12 series, the round head of GB70-76 The diameter is 18MM, which is smaller than the opposite side of chicagoDIN912, which is 18.27. In addition, the round head diameter of the inner hexagon GB70-76 of M16 and M20 series is 0.33MM smaller than that of chicagoDIN912, which are 24MM and 30MM respectively. chicagoDIN912 is 24.33MM and 30.33MM respectively. In addition, the width of the inner hexagon between the old standard and the German standard is different due to different standards. The inner side of GB70-76 is smaller, and it should be paid attention to in business operations. In addition, there are also some differences in the chicagocarriage screws that may be used at ordinary times. I will also make an explanation here. In the national standard, there are two standards for chicagocarriage screws, namely GB12 (small semicircular head square neck screw) and GB14 (large semicircular head square neck screw) Neck screws), and the German standard DIN603 is usually more commonly used in the market. Now to distinguish these three: for the round head and neck, when comparing the same specifications: GB12
With the rapid development of China's automobile industry, the requirements of body assembly process are constantly improving. Riveting has the characteristics of short process cycle, low noise and low energy consumption, and is widely used in automobile bodies. In the automobile industry, due to the complexity of the body sheet metal structure, there are many cavities, and the riveting tools in some positions will interfere with the structure. Many assembly points cannot use the traditional two-way loading riveting technology, so single-sided riveting is used instead. craft.
In the current production process, the inner wall of the circlip is quantitatively and evenly lubricated, and then the rotating shaft is inserted into the circlip, so that the rotating axis can rotate in the circlip, thereby realizing the rotation function of the sun visor. However, since the circlip is tightly fitted with the rotating shaft, during the insertion process of the rotating shaft, the front end of the circlip can easily push the grease from the opening at one end of the circlip to the opening on the other end of the circlip, so that the rotating axis and the inner wall of the circlip are easily connected. There is little or no grease left between them, which can easily lead to a lack of lubrication between the shaft and the circlip, and dry friction between the shaft and the circlip, resulting in a series of problems such as abnormal noise, difficult operation, and poor durability.
A screw belt structure, especially a screw belt that can position the screws on the screw belt, so that the screws do not swing, so that the screws can be stably aligned with the points where the screws are to be screwed, and the screw fixation of the screws is facilitated. In its overall implementation and use, the innovative design of the screw belt structure increases the practical function characteristics.
In order to achieve the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solution: a chicagosquare nut, including a nut body, the nut body is in the shape of a cube, the side length is 7.6mm, the height is 2.4mm, and the nut body is up and down. Both ends are respectively provided with a circular protrusion and a circular protrusion with a height of 0.25mm, the circular protrusion and the circular protrusion are respectively tangent to the upper and lower surfaces of the nut body which are square, and the circular protrusion and the circular protrusion are respectively tangent to the square upper and lower surfaces of the nut body. The protrusion and the circular protrusion are provided with a through hole in the middle and penetrate through the nut body. The opening of the through hole is provided with a chamfer of 30°, and the inner wall of the through hole is provided with a thread. There are several strip-shaped protrusions from the circumference inward to the opening of the through hole, and a number of strip-shaped grooves are arranged from the opening of the through hole outward to the circumference of the circular protrusion. There is a chamfer of 15° extending outward to the prism of the nut body.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: rounded chicagosquare nuts, ANSIB18.22.1A flat washers, black nickel hexagon socket head socket head chicagocap screws, B18.15 bolts and other products, we We can provide you with the right fastener solution for you.
