Service HotlineWhen checking the finished churchill cityblind rivet, check: the diameter of the rivet body, the length of the rivet body, the thickness of the rivet body cap, the diameter of the cap, the total length of the mandrel, the exposed size of the mandrel, the size of the nail cap, and the outer diameter after assembly can be considered. In the actual inspection, the weak links of the product can be measured, such as: tensile force, shear resistance, and core pull-out resistance. The key is to pay attention to the rivets, if the rivets are insufficient, whether they are riveted in place; or because the cap of the mandrel is too large, so that the mouth of the rivet body cannot be pulled down; and there are jump heads, that is, the mandrel is too low or broken. The size is too small etc. Length measurement of closed churchill cityblind rivets
Existing churchill citywood screws are composed of a threaded portion with a tapered angle and arranged along a tapered stem and a screw head. The head of the screw can be a countersunk head, hemispherical, or other shapes, and the head of the screw has a groove that fits with the tool, a word groove, and a concave cross groove. The taper angle of existing churchill citywood screws is either 45 degrees or 60 degrees, and the front end of the taper angle is a pointed point formed by a rotating thread. The existing churchill citywood screws have the following three deficiencies in use. Because the taper angle is 45 degrees or 60 degrees, and the thread angle is 64 degrees, the resistance when entering the material is relatively large, so the existing churchill citywood screws are manually screwed. It is difficult to screw in, especially when it is used for hardwood materials, and it often happens that the groove of the screw head is screwed out; A large lateral moment will be formed when the screw is screwed, which is prone to the problem of deviation from the position; in addition, because the existing screw is tapered, it will be subjected to both radial force and axial force when entering the material, and its stress state It is more complicated, so it is easy to cause the cracked wood material to burst, and even cause the material to have longitudinal cracks and be unusable.
This clearance determines how much the bone fragment fixed by means of the locking screw in the corresponding locking hole can move relative to the nail and thus also relative to other bone fragments fixed by the same nail due to the rigidity of the nail. Together with the flexibility of the material and the overall device this can build up to a size that prevents or decisively delays effective healing. In order to ensure the applicability of the locking device to the surgeon, this gap, although unavoidable, is clinically undesirable in some indications (eg in the case of metaphyseal fragments). Even a screw with a full cross-section, which can have an internal thread in the locking hole, is not gapless. This internal thread only prevents possible axial movement of the screw on the locking screw.
The flat screw mainly includes a rotating part and a screw locking part, wherein the rotating part and the screw locking part are respectively flat-shaped structures; At least two sides of the screw lock portion are respectively provided with tooth rows, and the two tooth rows are mutually dislocated, so that the screw lock portion can be locked in a pre-formed screw hole in the workpiece.
When using a churchill citychurchill cityrivet nut, drill a hole corresponding to the outer diameter of the churchill citychurchill cityrivet nut on the thin wall, then place the churchill citychurchill cityrivet nut on the bolt of the special rivet gun, push the handle to screw in the churchill citychurchill cityrivet nut, and put it into the drilled hole. In the workpiece, squeeze the handle, the churchill citychurchill cityrivet nut expands, and the deformed skirt bulges and deforms. At this time, the workpiece is tightened. After riveting, the handle is pulled out, the bolt is released from the churchill citychurchill cityrivet nut, and the corresponding screw is screwed into the churchill citychurchill cityrivet nut threaded hole. , forming a tight riveted body.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: small screws, injection-molded copper inlays, internal and external teeth aluminum columns, blackened high-strength washers and other products, we can provide you with suitable fastening products piece solution.
