Service HotlineThe material of the rubber gasket is NBR nitrile rubber, which is the most commonly used and has the highest cost performance. The use of FFKM perfluoroelastomer gaskets is generally in the more advanced fields, such as the field of aerospace rockets. Because its price is quite expensive, but its performance is excellent and can exceed many metal materials. For specific material information, please refer to the following: Material Name Chemical Description English Abbreviation English Alias Nitrile Butadiene Rubber Acrylonitrile-Butadiene Rubber Ethylene-Propylene-Diene Rubber EPDM EP,EPT,EPR Neoprene Neoprene CR Neoprene Silicone Silicone Rubber WMQ PVMQ Fluorosilicone Fluorosilicone Rubber FVMQ FVMQ Acrylate Acrylate Rubber ACM ACM Ethylene Acrylate Vinyl -Acrylic Rubber AEM Vamac Styrene-Butadiene Styrene-Butadiene Rubber SBR SBR Polyurethane Polyester/Polyether Urethane AU/Eu AU/EU Natural Rubber Natural Rubber NR NR
The side wall of the bolt hole is threaded, and the top of the nut is provided with several flattening notches. According to the locking nut of the preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the number of flattening notches is three. Due to the above features, the three flattening notches can be used as the focal point of the tightening tool, and the
Beneficial effects The commonly used nuts and bolts in the prior art are in the shape of a hexagon, the fastening surface is a regular hexagonal plane, and there are six elastic surfaces, and the adjacent elastic surfaces intersect with a straight line, and the opposite elastic surfaces are parallel to each other, In this way, the tightening operation can be easily performed with conventional tools, which is convenient and practical. However, there are some special occasions where the nuts and bolts of this structure are not suitable. Guangdong Yueluo Hardware Industry Co., Ltd. changed the fastening surface into a pentagon shape, and the adjacent elastic surfaces are connected by an arc angle. sex.
The meaning of bolt performance grade is an international standard. Bolts of the same performance grade, regardless of the difference in material and origin, have the same performance, and only the performance grade can be selected in the design. Strength grade The so-called 8.8 and 10.9 grades refer to the shear stress grades of bolts of 0.88GPa and 1.09GPa 8.8 Nominal tensile strength 800N/MM2 Nominal yield strength 640N/MM2 General bolts use XY to indicate the strength, X *100=tensile strength of this bolt, X*100*(Y/10)=yield strength of this bolt (because according to the regulations: yield strength/tensile strength=Y/10, that is, 0.Y is the yield strength ratio ) If the grade is 4.8, the tensile strength of this bolt is: 400MPa; the yield strength is: 400*8/10=320MPa. Another: stainless steel bolts are usually marked as A4-70, A2-70, and the meaning is otherwise explained Measurement: There are two main units of length measurement in the world today, one is the metric system, and the measurement unit is meters (m) and centimeters (cm). ), millimeter (mm), etc., are used more in Europe, my country and Japan and other Southeast Asian regions, the other is the British system, and the unit of measurement is mainly inches (inch), which is used more in the United States, Britain and other European and American countries. 1. Metric measurement: (decimal system) 1m2 =100 cm2=10000 mm2, imperial measurement: (8 decimal system) 1 inch = 8 inches 1 inch = 25.4 mm 3/8¢¢×25.4 =9.523, 1/4 ¢¢ The following products are indicated by their number, such as: 4#, 5#, 6#, 7#, 8#, 10#, 12#
The application range of the oil pump is very wide. When it is used, the oil pump needs to be assembled. During the assembly process, when the pin is driven into the pin hole, it is generally held by the operator with a hammer, and then aiming at the top of the pin to press. Into the hole, due to the relatively high tolerance requirements for the depth of the pin pressing and the side clearance (the gap between the pin and the groove wall), the traditional operation method not only causes a high rejection rate and a long training time for personnel, but also The slow processing speed affects the production efficiency.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head pin bolts, special nuts, thickened fasteners flat washers, non-slip hexagon nuts with washers and other products, we can provide you with suitable products for you fastener solutions.
