Service HotlineThe technical solution adopted by Yueluo to solve its technical problems is: a cabinet with a hidden screw type installation structure. The cabinet includes corner fittings, frame profiles and plates. Connecting slot, the plate installation slot is U shaped, the plate installation slot on the frame profile can be set with one or two, the insertion slot is located on the inner side of the plate installation slot; the main body of the corner fitting is fixed in three directions. The plug connector, the outer side of the plug connector is provided with auxiliary plate installation grooves, and the auxiliary plate installation groove is provided with side baffles; the plug connectors on the corner fittings are correspondingly inserted into the plug connectors on the frame profile, and the cross section of the plug connector Consistent with the cross-sectional size of the corresponding insertion slot, the plate is inserted between the plate installation slots on the frame profile.
In addition, the angle aluminum connection structure itself has structural defects of poor torsional and shear resistance, and many projects use larger insulating glass to meet the requirements of architects, resulting in a larger self-weight. In the event of a natural disaster such as an earthquake that will cause the curtain wall to shake violently, the bolts on the angle aluminum are prone to breakage, and the seismic performance is not good. Especially for the beam with the open structure, since the angle aluminum is installed in the opening cavity of the beam, the inertia moment of the beam is small, and the torsion resistance and shear resistance performance of the force are worse.
The existing method of tightening large screws is generally 1. After the nut is screwed to the connected piece by hammering + nut angle method, use a casing to connect the lever arm of the wrench, or use a free hammer to hammer the plate handle, Rotate the nut an additional angle to obtain the required preload. This is not only a primitive and labor-intensive fastening method, but also has great limitations, such as limited space, or the screw itself is a rotating shaft and so on, it is difficult to use this method.
Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 13 the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
With the development of the economy, automobiles have become an indispensable means of transportation in people's lives, and the production, sales and after-sales services of automobiles have also developed rapidly. Automobile wheels and steel rings are an important part of auto parts and are also related to The use of the car is safe. The connection between the car wheel and the steel ring is realized by bolts, so the bolts and nuts need to have good fixation.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Saigang POM washers, inner bolts with rings, cone washers, pressure riveting parts and other products, we can provide you with suitable fasteners for you. Firmware Solutions.
