Service HotlineGaskets are widely used in the machinery industry. According to the different needs of machinery and equipment in different industries, the structural forms of the sealing points are also different. Plum washer is one of the commonly used seals. It is commonly used between the pump and the motor coupling. In the actual production process of the enterprise, it is found that due to the influence of the material and structure, this type of gasket in common use can withstand impact force. Small, the septum is easily damaged. Because the current plum washers are all one-piece structures, even if one or several of the partitions are damaged, they need to be replaced as a whole. Although the value of a single plum washer is low, it needs to be shut down for maintenance and replacement almost every week. It also seriously affects the normal production of the enterprise, and the one-piece plum blossom gasket is also difficult to repair, adding unnecessary use costs to the enterprise. For this reason, the plum blossom gasket needs to be improved to strengthen the impact resistance of the gasket, and can be repeated Maintenance and use, prolong the maintenance cycle of the equipment, and ensure the normal production of the enterprise. The purpose of the utility model Yueluo is to solve the above-mentioned deficiencies in the existing technology, improve the existing technology, and provide a simple structure, which strengthens the impact resistance of the gasket, and can be repeatedly maintained and used to prolong the maintenance of the equipment. The cycle guarantees the plum blossom elastic washer normally produced by the enterprise. In order to achieve the above purpose, Yueluo is achieved through the following technical solutions-namely a plum blossom elastic washer, including an elastic washer body with a partition, the technical point is that the washer body is composed of a washer base and a partition that is independent of each other. , the septum and the gasket base are fixedly connected into one through the fixing piece. In order to further strengthen the impact resistance of Yueluo, the contact parts of the spacer and the washer base are respectively processed with a limited clamping table and a matching groove, so that the spacer and the washer base can be better integrated into one. According to the different specifications of the torx washer, the spacer and the washer can be fixed as a whole by rivets; or by screws. In addition, a semi-rigid tightening ring with grooves is embedded inside the washer base, and the width of the tightening ring is smaller than the width of the washer base; the ends of the rivets or screws are located in the grooves of the tightening ring, so as not to affect the performance of the torx washer JH is often installed. After the above improvement, Yueluo has improved the one-piece structure of the plum-blossom washer into a split structure and adopted a variety of fixed structure forms, so it has a simple structure, strengthens the impact resistance of the gasket, and can be repeatedly maintained and used. , Extend the maintenance cycle of the equipment and ensure the advantages of the normal production of the enterprise.
Stud bolts generally need to be surface treated. There are many types of bolt surface treatments. Generally, electroplating, blackening, oxidation, phosphating, and electroless zinc flake coating are commonly used. However, electroplated fasteners account for a large proportion of the actual use of fasteners. Especially in automobiles, tractors, home appliances, instrumentation, aerospace, communications and other industries and fields are more widely used. However, for threaded fasteners, not only a certain anti-corrosion capability is required in use, but also the interchangeability of threads must be ensured, which can also be called screwability here. In order to meet the dual-use performance of anti-corrosion and interchangeability required by threaded fasteners in use, it is very necessary to formulate special plating standards. GB/T5267.1-2002 [Threaded fastener electroplating layer] standard is one of the national standards fastener surface treatment series of standards, the standard includes: GB/T5267.1-2002 [fastener electroplating layer]; GB/T5267.2-2002 [Electrolytic zinc flake coating for fasteners] Two standards. This standard is equivalent to the international standard ISO4042; 1999 [Threaded fastener electroplating layer]. This standard replaces the GB/T5267-1985 [Threaded Fastener Electroplating Coating] standard.
The technical solution adopted by Yueluo to solve its technical problems is: a cabinet with a hidden screw type installation structure. The cabinet includes corner fittings, frame profiles and plates. Connecting slot, the plate installation slot is U shaped, the plate installation slot on the frame profile can be set with one or two, the insertion slot is located on the inner side of the plate installation slot; the main body of the corner fitting is fixed in three directions. The plug connector, the outer side of the plug connector is provided with auxiliary plate installation grooves, and the auxiliary plate installation groove is provided with side baffles; the plug connectors on the corner fittings are correspondingly inserted into the plug connectors on the frame profile, and the cross section of the plug connector Consistent with the cross-sectional size of the corresponding insertion slot, the plate is inserted between the plate installation slots on the frame profile.
According to the force of the connection, it is divided into ordinary and hinged holes. According to the shape of the head: there are hexagonal head, round head, square head, countersunk head and so on. Among them, the hexagonal head is the most commonly used. Generally, countersunk heads are used where connections are required. The English name of the riding bolt is U-bolt. It is a non-standard part. The shape is U-shaped, so it is also called a U-bolt. There are threads on both ends that can be combined with nuts. It is mainly used to fix tubular objects such as water pipes or sheets such as automobile plates. Springs are called riding bolts because of the way they fix things like a person rides a horse. According to the length of the thread, it is divided into two categories: full thread and non-full thread. According to the thread type, it is divided into two types: coarse thread and fine thread. The coarse thread type is not displayed in the bolt mark. The bolts are divided into eight grades: 3.6, 4.8, 5.6, 6.8, 8.8, 9.8, 10.9, and 12.9 according to their performance grades. Among them, the bolts above grade 8.8 (including grade 8.8) are made of low-carbon alloy steel or medium-carbon steel and are heat-treated (quenched). + Tempering), commonly known as high-strength bolts, and below grade 8.8 (excluding 8.8) are commonly known as ordinary bolts. Ordinary bolts can be divided into three grades: A, B, and C according to the production accuracy. Grades A and B are refined bolts, and grade C is rough bolts. For connecting bolts for steel structures, unless otherwise specified, they are generally ordinary rough grade C bolts. There are differences in the processing methods of different grades. Usually the corresponding processing methods are as follows: ① The bolts of grade A and B bolts are processed by lathes, with smooth surfaces and accurate dimensions. High, rarely used; ②C-grade bolts are made of unmachined round steel, the size is not accurate enough, and its material property grade is 4.6 or 4.8. The deformation is large during shear connection, but the installation is convenient and the production cost is low. It is mostly used for tensile connection or temporary fixation during installation.
Comparing the physical properties of stainless steel and carbon steel, the density of carbon steel is slightly higher than that of ferritic and martensitic stainless steel, but slightly lower than that of austenitic stainless steel; the resistivity is based on carbon steel, ferritic, martensitic and The order of austenitic stainless steel is increasing; the order of linear expansion coefficient is similar, austenitic stainless steel is the highest and carbon steel is the smallest; carbon steel, ferritic and martensitic stainless steel are magnetic, austenitic stainless steel is non-magnetic, But its cold work hardening will generate magnetism when it is transformed into intensite, and heat treatment method can be used to eliminate this martensitic structure and restore its non-magnetic properties. Compared with carbon steel, austenitic stainless steel has the following characteristics: 1) High electronegative rate, which is about 5 times that of carbon steel. 2) The large coefficient of linear expansion is 40% larger than that of carbon steel, and with the increase of temperature, the value of the coefficient of linear expansion of stainless steel screws increases accordingly. 3) Low thermal conductivity, about 1/3 of carbon steel.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: U-bolts, non-standard nuts, brass strut packs, brass flat washers and other products, we can provide you with suitable fasteners for you solution.
