Service HotlineThe elastic cylindrical pin, also known as the spring pin, is a headless hollow cylindrical body, which is slotted in the axial direction and chamfered at both ends. It is used for positioning, connection and fixation between parts. The outer diameter of the spring pin is usually slightly larger than the mounting hole. The deformation force generated by the elastic cylindrical pin to be restored to its original state by extrusion ensures the clamping effect of the elastic cylindrical pin. But just because of its clamping effect, it will play a big obstacle to the disassembly of the elastic cylindrical pin. When in use, the open end is extended out of the through hole on the pin shaft, and the open end is flared and separated to prevent the elastic cylindrical pin from sliding off the pin shaft to realize the function of preventing backlash. At present, the disassembly method of the elastic cylindrical pin usually uses a punching machine to remove the cylindrical pin, which easily destroys the equipment installed on the cylindrical pin, and the disassembled elastic cylindrical pin cannot be used again due to damage. One method is to insert the mounting pin with the clearance fit of the mandrel, punch the pin behind the mandrel to clamp the bottom of the cylindrical pin, and then pull out the cylindrical pin, which can only be used when the elastic mounting pin is installed in the through hole, and because it is necessary Applying force to the mandrel increases the difficulty of disassembly and increases the work intensity of the installer. Three methods are done by the installer using two needle nose pliers. Specifically, first use needle-nose pliers to clamp the ends of both sides of the elastic cylindrical pin, and then apply an inward force to the needle-nose pliers, so that both sides of the elastic cylindrical pin rotate in the same direction until the opening becomes smaller, and then Pull it out to remove it successfully. The defects of these existing methods are obvious. The shape of the disassembled elastic cylindrical pin is either unusable or the deformation of the cylindrical pin after disassembly is not uniform, which seriously affects the performance of the elastic cylindrical pin, resulting in waste and increased cost; The method is purely manual work, and sometimes it takes several repetitions to remove the elastic cylindrical pin. Due to the different installation positions of the elastic cylindrical pin, it sometimes increases the difficulty of disassembly, and it is difficult to remove the needle-nose pliers effectively. The pliers are difficult to construct, and the elastic cylindrical pins are easily damaged. If there are too many elastic cylindrical pins to be disassembled, the existing methods are often difficult to meet the needs, which not only consumes a lot of time and physical strength of the installer, but also makes it difficult to ensure the quality.
1. Fixed anchor bolts, also known as short anchor bolts, are poured together with the foundation and used to fix equipment without strong vibration and impact. 2. The movable anchor bolt, also known as the long anchor bolt, is a detachable anchor bolt used for fixing heavy machinery and equipment with strong vibration and impact. 3. Expansion anchor bolts are often used to fix stationary simple equipment or auxiliary equipment. The installation of expansion anchor bolts should meet the following requirements: the distance from the center of the bolt to the edge of the foundation shall not be less than 7 times the diameter of the expansion anchor bolt; the foundation strength of the expansion anchor bolt shall not be less than 10MPa; there shall be no cracks in the drilling holes. The drill bit collides with the steel bars and buried pipes in the foundation; the diameter and depth of the drill hole should match the expansion anchor bolts. 4. The bonding anchor bolt is a kind of anchor bolt commonly used in recent years, and its method and requirements are the same as the expansion anchor anchor bolt. However, when bonding, pay attention to blowing out the debris in the hole, and do not get wet. [1]
In addition, the angle aluminum connection structure itself has structural defects of poor torsional and shear resistance, and many projects use larger insulating glass to meet the requirements of architects, resulting in a larger self-weight. In the event of a natural disaster such as an earthquake that will cause the curtain wall to shake violently, the bolts on the angle aluminum are prone to breakage, and the seismic performance is not good. Especially for the beam with the open structure, since the angle aluminum is installed in the opening cavity of the beam, the inertia moment of the beam is small, and the torsion resistance and shear resistance performance of the force are worse.
The core rivet is a new type of riveting fastener that is very convenient for riveting. It can show its unique advantages in a relatively small space or in an environment where there is no rivet gun or a rivet gun cannot be used. Two or more connected parts can be riveted successfully by hitting the mandrel on one side with a hammer or other utensils. Core rivets can be divided into oblate head core rivets and countersunk head core rivets according to the shape of the brim of the nail cap. According to different material combinations, they can be divided into all aluminum core rivets, aluminum steel core rivets, and all stainless steel core rivets. Rivets, steel rivets, aluminum stainless steel rivets, plastic rivets, etc. Core rivets do not have to be riveted with manual riveting guns or pneumatic riveting guns like blind rivets. They have better riveting and convenience, and can be widely used in the riveting of various connected parts.
Slotted round nut, side hole round nut, end face hole round nut, small round nut round nut, ring nut, wing nut copper nut, inlaid copper nut, knurled copper nut, embedded copper nut, injection copper Nuts and other alloys zinc-copper alloy nuts and other anti-loosening principles Edit the locking nut The locking nut DIC-LOCK locking nut is composed of two parts, each part has a staggered cam, due to the internal wedge design, the slope angle is greater than the bolt's The angle of the nut, the combination is tightly integrated into a whole. When vibration occurs, the raised parts of the DIC-LOCK locknut stagger with each other to generate lifting tension, thereby achieving the anti-loosening effect.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: enlarged washers, hexagon socket shoulder screws, blackened bucket bolts, top blasting screws and other products, we can provide you with suitable products for you. Fastener Solutions.
