Service HotlineThe diameter, length and quantity of the stud bolts shall meet the requirements, and the type and material of the stud bolts shall be determined by the grade. There are two types of commonly used stud bolts (also known as full-threaded studs). The thread is divided into two types: coarse thread and fine thread. The coarse thread ordinary thread is expressed by M and the nominal diameter, and the fine thread ordinary thread is expressed by M and the nominal diameter × pitch. The fastener standard stipulates that M36 bolts use coarse thread, M36 and above diameters can use fine thread, and the pitch is 3. bm=1d studs are generally used for the connection between two steel connected parts; bm=1.25d and bm=1.5d studs are generally used between cast iron connected parts and steel connected parts The connection between the two; bm=2d double-ended stud is generally used for the connection between the aluminum alloy to be connected and the steel to be connected. The former connector has internal threaded holes, and the latter connector has through holes. The threads at both ends of the equal-length studs need to be matched with nuts and washers, and are used for two connected parts with through holes. One end of the welding stud is welded on the surface of the connected piece, and the other end (threaded end) passes through the connected piece with a through hole, and then the washer is put on, and the nut is screwed on, so that the two connected pieces are connected as a whole.
In view of the deficiencies of the prior art, Guangdong Yueluo Hardware Industry Co., Ltd. provides a relatively simple screw that can be manually disassembled. In order to achieve the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical scheme: a screw that can be disassembled manually, including a stud and a nut, and the axial direction of the screw is provided with a screw extending from the nut to the stud. A groove, a control column that is slidably matched with the groove is arranged in the groove, a through groove is opened on the circumferential side wall of the control column, and a circumferential side wall of the control column is provided with a parallel to the axis of the control column. A limit bar, the side wall of the groove is provided with a limit groove that cooperates with the limit bar, the control column is provided with a accommodating groove, and the accommodating groove is provided with a rotating rod that cooperates with the through groove, so The accommodating groove and the rotating rod are arranged separately. Further, a accommodating groove is opened at the corresponding groove on the nut, a baffle is hinged on the side wall of the accommodating groove, and a torsion spring is provided at the hinged joint between the baffle and the accommodating groove.
The profile of the American National thread (60 profile angle and H/8 flatness) is different from the Wyeth thread profile (55 profile angle and H/6 flattening height). American National Thread is widely used in regions and industries that are influenced by American industry. In World War II, due to the inconsistent thread standards used by the Allies, the logistical supply difficulties caused serious economic losses and casualties to the Allies. Immediately after the end of World War II, the United States, the United Kingdom, Canada and other allies immediately began to formulate a unified thread standard among allied countries, and promulgated a unified thread standard in 1948. Because the economic strength and military strength of the United States dominated the Allied forces at that time, the unified thread was mainly formulated according to the national thread standard of the United States. Unity; the latter letter N is derived from the N designation for American National Threads. Since then, the unified thread began to squeeze the original use market of the British Whitworth thread.
Hexagon head bolts are divided into two types: outer hexagon bolts and inner hexagon screws. According to the force mode of the connection, there are ordinary ones and those with reaming holes. The bolts used for reaming holes should be matched with the size of the holes and are used when receiving lateral force. According to the shape of the head, there are hexagonal head and round head. , square head, countersunk head, etc. Generally, the countersunk head is used in places where the surface is smooth and no protrusions are required after connection, because the countersunk head can be screwed into the part. The round head can also be screwed into the part. The tightening force of the square head can be Larger, but larger in size. Hexagons are the most commonly used. In addition, in order to meet the needs of locking after installation, there are holes in the head and holes in the rod. These holes can prevent the bolts from loosening when they are subjected to vibration.
Screws are a common type of fastener on the market. It is a type of fastener consisting of a head and a screw. It can be divided into three categories according to its purpose: machine screws, set screws and special purpose screws. Machine screws are mainly used for a fastened connection between a part with a fixed threaded hole and a part with a through hole, without the need for nut matching (this connection form is called screw connection, which is also a detachable connection; it can also be Matching with nuts, it is used for fast connection between two parts with through holes.) Set screws are mainly used to fix the relative position between two parts. Special purpose screws, such as eyebolts, are used for hoisting parts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat washers with missing corners, chrome vanadium steel heat treatment precision machining, carbon steel twelve angle flange nuts, blackened and thickened fixed washers and other products. We can provide you with the right fastener solution for you.
