Service HotlineSelf-tapping screw is a kind of threaded fastener that self-tapping and drilling the matching female thread in the pre-drilled hole of metal or non-metal material. When using self-tapping screw, a flat washer is often required to protect the fastening surface. Traditional When the self-tapping screw is used, the flat pad is easy to fall off, resulting in low work efficiency. In view of this, we propose a combined structure of the stuck self-tapping screw spring washer that prevents the flat pad from falling off.
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 447N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
The classification of the second combination screw is divided according to the material of the screw wire and the hardness index of the screw wire. Generally, the two combination screws are divided into stainless steel and iron, and stainless steel is divided into stainless steel 201, stainless steel 304 and stainless steel 316. Iron is divided into three types: low carbon steel, medium carbon steel, and high carbon steel. Carbon steel combination screws refer to iron combination screws. Generally, iron combination screws are classified into grades 4.8, 8.8, 10.9, and 12.9. But in the market, the combination screws of grade 10.9 and grade 12.9 are rarely used, so we won't talk about it here. And the two combination screws on the market are more commonly used combination screws of grade 4.8 and 8.8. 4.8 grade combination screws are generally made of 1010A screw wire rods. After the screw wire rods are beaten into screws, they are combined with spring flat washers. After production, this 4.8 grade combination screw does not need to be hardened. Its hardness can reach 4.8. The 8.8 grade combination screw is generally made of 10B21 screw wire. After the screw wire is punched into a screw, it is equipped with a spring washer and a flat washer, and the three pieces can be combined and rubbed by an automatic spring-flat washer machine. Fasten the spring-flat washer combination on the screw, and the spring-flat washer will not fall off. After the combination screw is produced, it needs to be hardened to make the hardness reach 8.8. After the hardness reaches 8.8, we need to take it for electroplating. In order to prevent hydrogen embrittlement of the spring washer in the 8.8-level combination screw with added hardness, it is easy to break. In this way, it is necessary to carry out hydrogen removal treatment on the hardened combined screws, and the electroplating can only be done after the hydrogen removal.
In order to overcome the technical problem that the screws and nuts cannot be disassembled and assembled at the same time in the prior art, Guangdong Yueluo Hardware Industry Co., Ltd. provides a simple structure and can be quickly disassembled and assembled at the same time in a small space. screw and nut removal tool.
In the prior art, the screw suction device can be implemented in the following two ways. One is to use a magnet to magnetize the electric bit head, and the electric bit head is used to approach the screw, and the screw is stuck by the electric bit head, so that the function of picking up the screw can be realized; The vacuum generator is used to form a negative pressure in the screw guide groove, and the screw is sucked into the tube to realize the screw pickup. The disadvantage of this solution is that in the process of picking up the screws, the grooves of the screws cannot be aligned, which leads to the deviation or leakage of the screws. The disadvantage of this solution is that the screw with an aspect ratio of less than 1.5 is prone to suction and skew, and the stability is not high. It can be seen that the existing technology still needs to be improved and developed.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: screws with flat spring washers, non-slip washable screws, rivet nuts, corrosion nylon screws and other products, we can provide you with suitable screws for you. Firmware Solutions.
