Service HotlineGuangdong Yueluo Hardware Industry Co., Ltd. has upgraded and combined the fastening nut and the hexagonal nut to ensure the original function of the nut. The nut can be easily and safely disassembled by preparing practical small parts. The inner diameter of the lock ring is 0.1mm larger than that of the hexagonal nut, which is convenient for installation.
1) Scope This standard specifies the lock nut (referred to as nut), the size of the locking device, technical requirements, acceptance rules and measurement methods. This standard applies to the design, production, inspection and user acceptance of nuts and locking devices for tapered bushings. 2) Terminology The terms used in this standard conform to the provisions of GB/T 6930. This standard specifies the marking system, index, test method and marking of the mechanical and working performance of the effective torque section steel hexagonal lock nut. This standard is applicable to coarse thread 6H class nuts made of carbon steel or alloy steel, the width across the sides conforming to the provisions of GB 3104, the nominal height is ≥ 0.8D, and the guaranteed load and effective torque need to be specified, and the thread diameter is 3 ~ 39mm. Except for the effective torque part, the thread size and tolerance are specified in GB 193, GB 196 and GB 197. The working temperature range of the nut should be in accordance with: All-metal nut without electroplating treatment: -50℃～+300℃. All-metal nuts with electroplating treatment: -50℃～+230℃; nuts embedded with non-metallic elements: -50℃～+120℃. This standard does not apply to nuts with special performance requirements (such as weldability and corrosion resistance). For stainless steel and non-ferrous metals with fine pitch lock nuts or thin nuts made of carbon steel or alloy steel, the performance indicators and test methods of effective torque specified in this standard may be adopted by mutual agreement.
When processing some disc parts, the mandrel is often used for positioning, and the nut is pressed on it. However, the ordinary nut cannot meet the requirements due to its small end face and poor flatness. The user needs to make the nut, and the cost is high due to single-piece production.
Installation method broadcast 1. One-time burying method: When pouring concrete, bury the anchor bolts. When the high tower is controlled by overturning, the anchor bolt should be buried once. 2. Reserved hole method: The equipment is in place, the holes are cleaned, the anchor bolts are placed in the holes, the equipment is positioned and aligned, and then poured with non-shrinkage fine stone concrete that is one level higher than the original foundation, and compacted and compacted. . The distance from the center of the anchor bolt once buried to the edge of the foundation should not be less than 2d (d is the diameter of the anchor bolt), and should not be less than 15mm (d≤20, it should not be less than 10mm), not less than half the width of the anchor plate Add 50mm, when the above requirements cannot be met, appropriate measures should be taken to strengthen it. The diameter of the anchor bolts used for the structure should not be less than 20mm. When subjected to earthquake action, double nuts should be used for fixing, or other measures to effectively prevent loosening should be adopted, but the anchorage length of anchor bolts should be increased by 5d compared with the anchorage length of non-seismic action. Installation planning of anchor bolts Treatment of anchor bolts loose in the foundation When the anchor bolts are tightened, the bolts may be pulled out. At this time, the bolts should be adjusted to their original positions, and the foundation around the bolts should be shoveled out enough. , and then weld two U-shaped steel bars vertically and horizontally on the bolts, and finally clean the pit with water and grouting, and then tighten the live anchor bolts after the concrete has solidified to the design strength. The treatment method of the live anchor bolt deviation is roughly the same as the dead ground. The method for the anchor bolts is the same, except that the anchor bolts can be pulled out for processing. If the bolt is too long, a section of the thread can be cut off on the machine tool; if the bolt is too short, it can be extended by hot forging; if the position is inconsistent, it can be corrected by bending. Application industry: suitable for various equipment fixing, steel structure foundation embedded parts, street lights, traffic signs, pump, boiler installation, heavy equipment embedded fixing, etc.
The marking format of the thread mark is: Thread code - thread tolerance zone code (pitch diameter, top diameter) - screw length l) Tolerance zone code is represented by numbers plus letters (inner thread with uppercase letters, external thread with lowercase letters) , such as 7H, 6g, etc., it should be specially pointed out that 7H, 6g, etc. represent thread tolerance, while H7, g6 represent cylinder tolerance code. 2) The length of rotation is specified as short (represented by S), medium (represented by N), and long (represented by L). In general, the thread engagement length is not marked, and the thread tolerance zone is determined by the medium engagement length (N). If necessary, add the screw length code S or L, such as M20-5g6g-L. When special needs are required, the value of the screwing length can be indicated, such as M20-5g6g-30.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Shanghai warehouse screws, hand percussion rivets, butterfly screws and bolts, plastic round flat washers and other products, we can provide you with suitable products for you. Fastener Solutions.
