Service HotlineThe contact surface between the existing chassis and the main board is generally not a horizontal plane due to processing reasons, especially the main board is prone to warping deformation. It will increase, resulting in deformation of the motherboard and poor memory contact, affecting normal use.
Half round head rivets are mainly used for riveting occasions with large lateral loads, and are the most widely used. Flat cone head rivets are often used in riveting occasions with strong corrosion such as ship hulls, boiler water tanks, etc. Countersunk head and 1200 countersunk head rivets are mainly used for riveting occasions where the surface must be smooth and the load is not large. Half countersunk head and 1200 half countersunk head rivets are mainly used for riveting occasions where the surface must be smooth and the load is not large. Flat head rivets are used for riveting occasions with general load. Flat head and flat head rivets are mainly used for riveting of metal sheets or non-metallic materials such as leather, canvas and wood. Large flat head rivets are mainly used for riveting of non-metallic materials. Semi-hollow rivets are mainly used for riveting occasions with small loads. Headless rivets are mainly used for riveting of non-metallic materials. Hollow rivets are light in weight and weak in head, and are used for riveting of non-metallic materials with small loads. Tubular rivets are used for riveting of non-metallic materials without load. Nameplate rivets are mainly used for riveting nameplates on machines and equipment.
Metric threads are measured in MM (millimeters) and have a cusp angle of 60 degrees. Both US and Imperial threads are measured in inches. The cusp angle of the American thread is also 60 degrees, while the cusp angle of the imperial thread is 55 degrees. Due to the different units of measurement, the representation methods of various threads are also different. For example, M16-2X60 represents a metric thread. His specific meaning is that the nominal diameter of the screw is 16MM, the pitch is 2MM, and the length is 60MM. Another example: 1/4—20X3/4 means the inch thread, what he specifically means is the nominal diameter of the screw It is 1/4 inch (one inch = 25.4MM), there are 20 teeth on one inch, and the length is 3/4 inch. In addition, if you want to express American screws, UNC and UNF are usually added to the back of the British screws to distinguish between American coarse teeth or American fine teeth. In the usual domestic sales business, the most common standards we encounter are GB (National Standard) and DIN (German Standard). In the production of Yaoda, the following standards are mainly encountered: GB30; GB5783; GB5782; GB52; GB6170; GB818; GB819; GB845; GB846; GB70; DIN912; DIN933; It has been replaced by GB5783 (new national standard). GB52 (old national standard) has been replaced by GB6170 (new national standard) in the standard book.
rivet automatic feeding device comprises a feeding installation frame, the upper end of the feeding installation frame is provided with a horizontally arranged receiving block mounting plate, the upper surface of the receiving block installation plate is provided with a rivet receiving block, a rivet The upper surface of the receiving block is provided with a receiving block movable groove that opens upward and completely penetrates left and right. The left movable receiving rod can be embedded in the receiving block movable groove relatively movably, and the right movable receiving rod is located on the right end side of the left movable receiving rod. The receiving rod, the right end of the left movable receiving rod is provided with a left receiving groove that opens upward, and the left end of the right movable receiving block is provided with a right receiving groove that opens upward;
Traditionally, the pressure rivets on the product are all beaten by hand by workers, resulting in high scrap rate and low efficiency, and this rivet is not a traditional rivet, so it is difficult to locate and requires high pressure. The rivets are thin, and the pressure is too large to cause deformation of the rivets. If the pressure is too small, it cannot be riveted. Without special positioning and tooling, it cannot be riveted on the riveting machine. The quality of the products produced in this way is difficult to guarantee, and the quality levels of the products in the same batch are uneven. Affect delivery time.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: O-type screws, hexagonal nylon copper posts, female screw thread connections, hexagonal fine-tooth nuts and other products, we can provide you with products suitable for you fastener solutions.
