Service HotlineType 1 nut refers to an ordinary hexagonal nut with a nominal height of m ≥ 0.8D. Its type and size should meet the requirements of GB/T6170; while the height of type 2 nut is higher than that of type 1 nut, its type and size should comply with GB/T6170. T6175. There are two purposes to increase the type 2 nut: one is to obtain a relatively inexpensive nut that does not require heat treatment by increasing the height of the nut. Because D≤M16 grade 8 type 1 nuts do not need heat treatment, among grade 8 nuts, only the specifications of D>M16~39 use type 2 nuts. Obviously, type 1 nuts that do not need heat treatment cannot reach grade 9 nuts. Mechanical property requirements. Another purpose of specifying Type 2 nuts is to obtain a more ductile grade 12 nut. As the height of the nut increases, the guaranteed stress index can be achieved at a lower quenching and tempering hardness, so the toughness of the nut is increased. Classified by tooth spacing: standard teeth, regular teeth, fine teeth, very fine teeth and cross teeth. Classification by material: stainless steel hexagon nuts and carbon steel hexagon nuts, copper hexagon nuts, iron hexagon nuts. Classification by thickness: hexagonal thick nuts and hexagonal thin nuts. Classification by usage: hot melt copper nut, hot pressed copper nut, embedded copper nut and ultrasonic copper nut
Usually, the car wheel is fixed on the axle sleeve with positioning pins and pins, and the tire hub and the sleeve are fastened on the axle with locking nuts, lock washers, and adjusting nuts. This structure can operate normally within a certain period of time when the vehicle speed is low and the vibration is small. However, when the car runs for a long time, especially when the road surface is uneven and the load changes sharply, the axle sleeve bears a great impact. Once the shear force generated is too large, the pin will break, and the nut will be loosened. Affected, the wheel and hub will be loose. If the maintenance is not timely, or the driver is inexperienced, the car will have an accident in which the tire falls off with the wheel hub. This is extremely dangerous. So people are looking for ways to prevent wheels and hubs from falling off
screw assembly includes a screw body, a spring and a mounting plate, the screw body includes a nut and a screw, the top of the screw is provided with a polygonal notch, the screw is composed of upper and lower parts, and the diameter of the upper part of the screw is larger than that of the lower part of the screw A slot is arranged at the lower end of the upper part of the screw rod; a slot corresponding to the spring is arranged on the mounting plate, and an extension slot is arranged in the slot, and the extension slot is L-shaped; an extension body is arranged at one end of the spring , the extension body corresponds to the extension slot; the spring is installed between the nut and the mounting plate, and the spring extension body is installed in the slot extension slot. Guangdong Yueluo Hardware Industry Co., Ltd. has the following advantages: it can prevent the spring from rotating with the rotation of the screw, the structure is simple, and the use is convenient.
With the rapid development of China's automobile industry, the requirements of body assembly process are constantly improving. Riveting has the characteristics of short process cycle, low noise and low energy consumption, and is widely used in automobile bodies. In the automobile industry, due to the complexity of the body sheet metal structure, there are many cavities, and the riveting tools in some positions will interfere with the structure. Many assembly points cannot use the traditional two-way loading riveting technology, so single-sided riveting is used instead. craft.
Currently, a screw generally includes a shank body, a threaded portion formed on the outer edge of the shank body, and a conical head formed at the rear end of the shank body. When the current thread is in use, since the thread part is cylindrical, the thread part and the workpiece are vertical, so it is relatively laborious when in use, and it is difficult to locate, lock and unlock.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head vertical grain aluminum rivet nuts, copper embedded parts, pressure riveting screws, hook screws and other products, we can provide you with suitable products for you fastener solutions.
